You guys want a laugh at my expense? Its pretty funny :).

A place for general discussion. Catch up with mates, post pics, or if you just want to pick on e-thugs.
ProZac
G33Kz0r
Posts: 2674
Joined: Thu Nov 27, 2003 1:26 pm
Location: Christchurch, New Zealand
Contact:

You guys want a laugh at my expense? Its pretty funny :).

Post by ProZac »

This has convinced me i shouldn't be allowed near a spanner for a week, its about the stupidest thing ive ever done when it comes to cars... a total oversight.

As some of you might have seen, i changed the turbo, and added an intercooler to my car the other day, it was all factory starion gear, so no majour hassels to fit, just a bit of cutting here and there. The turbo i aquired felt in pretty good condition, and used to be on my old car, it never gave me any problems there, so i was expecting it to be sweet as. I put the thing back together, clamped on the exhaust housing with some sealant, bolted on the WG actuator, made a gasket and bolted on the oil return pipe. Bout an hour later it was all fitted to the car, i clean up and fired her up. SWEET! started first pop, sounds much nicer than before, as there are no exhaust leaks. COOL!

Headed inside, washed my hands and let it idle for a couple of mins, came out and its chugging blueish smoke, stinking of burnt oil. Bugger i thought, the seals are gone, ahh well, i have a couple of other mitsy CHRA unit, i'll try another tomorrow. No biggie.

Tomorrow comes, i strap on my overalls, remove the turbo and take it to the garage to pry it apart and clean up the housings. After pouring all the oil out of it, about 500ml (no shit), I took off the oil return pipe, screamed, kicked myself in the face, ran face first into the garage door and passed out. Sometime later i woke up and had a good chuckle. You see people, when you make a gasket, its very important to MAKE A FUCKING HOLE IN IT SO THE OIL CAN ACTUALLY PASS! Hahahaha. I punched out the boltholes fine, then put it together, effectivley sealing off the oil return pipe. God damn. I Figured i'd totally stuffed the seals now, but i put it back together and tried it out anyway... After all the residual oil burned off, it seems to be going sweet as, quiet, no leaks and best of all, NO SMOKE!

Now hows that for moronic? eh? eh?

Zac.
User avatar
scum
I'm Banned!
Posts: 1412
Joined: Fri Jan 09, 2004 12:49 pm
Location: Perth WA

Post by scum »

whats your address? i want to mail you a slap, fool. :D
I figured out the meaning of life, and since then every day just gets worse.

Warranty void if stupid.
User avatar
MelbStazz
Enthusiast king
Posts: 866
Joined: Thu Jan 08, 2004 2:55 pm
Location: Melbourne

Post by MelbStazz »

aaaah zac.
rofl
- el schmicko detailer -
WidebodyWoody
Woodwide
Posts: 3133
Joined: Thu Jan 08, 2004 6:24 pm
Location: Gold Coast
Contact:

Post by WidebodyWoody »

Why can't we let you near a spanner again for a week? It should be more like not letting you near a Starion again for a year, j/k
nashstyle
I've been here before
Posts: 211
Joined: Thu Apr 22, 2004 4:19 pm
Location: Blackburn, Melbourne
Contact:

Post by nashstyle »

Hahaha, GOLD JERRY, GOLD!
I liek to flutter.
CussCuss
6pack esky
Posts: 1294
Joined: Fri Jan 09, 2004 1:34 pm
Location: Sydney

Post by CussCuss »

hahaha, everyone has their moments of stupidity, just think yourself lucky that it didnt cause any major problems
User avatar
TD05
it's probably their firewall
Posts: 1404
Joined: Sun Jan 11, 2004 11:23 am
Location: Brisbane

Post by TD05 »

as long as we can all hava laugh rofl

no worse than the time I (read forgot) left my 1/2 in drive complete with 19mm socket on the crank bolt, when I started the motor, the bloody thing hit the floor at 50 kh, smashing the socket to smithereens, not to mention the noise it made !! shat meself, almost.. :oops:
Kiss my st AZZ -
Starions rule the sports car world
GTI-R's are best in the wet..
Who needs Rock & Roll when there's JAZZ, Honda RULEZ
User avatar
Darkelf
RiceKing!
Posts: 640
Joined: Thu Jan 08, 2004 2:25 pm
Location: Sydney

Post by Darkelf »

LOL and you guys have the cheek to have a go at me!
User avatar
Cookiemonster
Mother Goose
Posts: 3177
Joined: Thu Jan 08, 2004 4:33 pm
Location: Sydney

Post by Cookiemonster »

Darkelf wrote:LOL and you guys have the cheek to have a go at me!
Just because Zac is dumb doesn't mean you're smart.
User avatar
Alspos
Flucking kwankers
Posts: 4107
Joined: Thu Jan 08, 2004 2:09 pm
Location: Melbourne
Contact:

Post by Alspos »

rofl

*grabs tissue to mop up tears from laughing so hard*
User avatar
WANTSOM
Pushing my luck
Posts: 2115
Joined: Mon Jan 12, 2004 1:43 pm
Location: Sydney

Post by WANTSOM »

rofl at 'zac and also even more so at Kelfy. God mate, why do you set yourself up so much.

Cookie, its like swatting flies with Kelfy hey :D
Never argue with an idiot, it brings you down to their level and they beat you with experience.
User avatar
merlin
Enthusiast
Posts: 658
Joined: Sun Jan 11, 2004 5:51 pm
Location: Sydney, Australia

Post by merlin »

that was lovely Zac, made it worth the effort to come into work and logon.
thanks for sharing, priceless.
i'd tell you about some of mine, but alas, i forget.
User avatar
Defective
Enthusiast
Posts: 706
Joined: Thu Apr 15, 2004 10:43 pm
Location: Nelson, South island
Contact:

Post by Defective »

hahahahahahahahahahahahahahahahahahahahahahhaha....


thats great, that has just made my day :D :D :D :D


and the socket set left in the engine bay? ive done that too :x

sounded like someone had just shot at my car....
oz, here i come....
User avatar
Darkelf
RiceKing!
Posts: 640
Joined: Thu Jan 08, 2004 2:25 pm
Location: Sydney

Post by Darkelf »

WANTSOM wrote:rofl at 'zac and also even more so at Kelfy. God mate, why do you set yourself up so much.

Cookie, its like swatting flies with Kelfy hey :D
You guys love it! :)
User avatar
madeofmilo
Enthusiast
Posts: 578
Joined: Fri May 21, 2004 5:53 pm
Location: Melb - East

Post by madeofmilo »

If you need to get any work done I know a good mechanic in Dandenong (Melb sorry:P)....

Oh no wait that guy screwed me OVER!!

**Dave cries and can't live down the pain of being ripped off**

Dave
My JA has perfect motor - FMIC - forgies - high flow head but...rusted front guards and keyed on every panel. Time to get serious or time to take it to the tip.
Post Reply

Who is online

Users browsing this forum: No registered users and 25 guests