GH Pigma. VR4 Head + Forged Stroker..

davidbek95 · Post by **davidbek95** » Tue Jun 29, 2010 9:18 pm

Anchor,
I told you,you would get a good deal,as far as i am concern chris is the number engine builder,as i have one of his motors.
regards david

Anchor · Post by **Anchor** » Wed Jun 30, 2010 1:50 pm

JMF Race RWD 4g63 intake manifold for the Pigma. And a free t-shirt.

Big thanks to jim. Easy as to order/pay/recieve.

1320ft · Post by **1320ft** » Wed Jun 30, 2010 11:40 pm

Was that direct from JMF? I have been looking at the DSM Drag manifold.

siggy_gsr · Post by **siggy_gsr** » Thu Jul 01, 2010 10:26 am

Can't recommend Jim from jmf any more.. Heaps good to deal with... Also running one of their manifolds... Deal with him direct, he has a supplier on the central coast in nsw but he wanted like double the price...

Anchor · Post by **Anchor** » Thu Jul 01, 2010 1:33 pm

Yeah email them direct. Their supplier in NSW couldn't come close to Jims price. Which is kinda weird..

NXTIME · Post by **NXTIME** » Thu Jul 01, 2010 5:27 pm

1320ft wrote:Was that direct from JMF? I have been looking at the DSM Drag manifold.

Hypertune no good? Or too exxy?

Lummy · Post by **Lummy** » Thu Jul 01, 2010 5:47 pm

May I ask what that intake cost?

iXNAY · Post by **iXNAY** » Thu Jul 01, 2010 5:53 pm

JMF or Magnus = alot better vaule for money in comparison to hypertune!

1320ft · Post by **1320ft** » Thu Jul 01, 2010 11:14 pm

NXTIME wrote:
1320ft wrote:Was that direct from JMF? I have been looking at the DSM Drag manifold.
Hypertune no good? Or too exxy?

Honestly, to exxy. I rang them the other day & I wont get much change from 2K. I am going to ring them again tomorrow though as "Aaron from Burson Parra" and see if that gets it any better.

Even Plazmaman manifolds are only $1100 polished.

siggy_gsr · Post by **siggy_gsr** » Fri Jul 02, 2010 1:09 am

Think mine was about $800 AUD delivered and polished... Dollar was really good then too..

NXTIME · Post by **NXTIME** » Fri Jul 02, 2010 8:30 am

Aaron, tell them that you have a rule: "You won't use any mods that cost more than the car" :D

See if they might sponsor you ;)

I wonder if the Chinese have made 'copy' plenums yet ;)

Anchor · Post by **Anchor** » Fri Jul 02, 2010 1:01 pm

There are a few copy plenums out there. But i'd rather spend the money.. Talking of money, i think this one cost me around the $800 mark landed. Not bad.. Considering the dollar is half ok.

greenstaz82 · Post by **greenstaz82** » Fri Jul 02, 2010 3:11 pm

i have the same intake on my starion , best priced quality intake , im running the same kinda setup as u .

1320ft · Post by **1320ft** » Fri Jul 02, 2010 8:06 pm

NXTIME wrote:Aaron, tell them that you have a rule: "You won't use any mods that cost more than the car" :D

See if they might sponsor you ;)

Lol, well the car only cost me 1k to buy!

Rang them today (hypertune), the manifold would cost me $1400 + throttle body $528 trade price.

Retail is $1760 on the manifold & $660 for the 90mm throttle body.

NXTIME · Post by **NXTIME** » Fri Jul 02, 2010 11:28 pm

still too much. I know that there are other similar TB's for $150-200.

Someone should do a group by on some Chinese copies ;)

Austarion

GH Pigma. VR4 Head + Forged Stroker..

good deal

Who is online