pics of my jb 50% back to bare metal

igottasicjb · Post by **igottasicjb** » Mon Jul 02, 2007 10:11 pm

Still allot of work to go but this is about 20 hours into it, still requires touch ups but I’ll go over the whole car again to do that.
The interior in about 85% clean and the exterior in about 35% clean

I’ve still yet to get to the under body and not looking forward to it

:

starspeed · Post by **starspeed** » Mon Jul 02, 2007 10:56 pm

OHMYGOD , Its getting there :) , and alot to go , being there done that !!!! , keep that chin up

:D :beer

MrBishi · Post by **MrBishi** » Tue Jul 03, 2007 6:56 am

Any hidden surprises yet?

igottasicjb · Post by **igottasicjb** » Tue Jul 03, 2007 12:00 pm

The only surprises I’ve found is around the middle of the firewall but its not much and the bottom corners of the windscreen and the top sills of the doors.
There is a little bit of filiform corrosion (looks like spider web marks) around some of the spot welds but nothing the sandblaster won't fix. Other than that the car is rust free so far. Which is surprising considering the age of the vehicle,

I got some good paint stripper from work so it makes it allot faster. Not even polished 2 Pac can stop this stuff, only problem if it farkin hurts like hell when it gets on you :o

redzone · Post by **redzone** » Tue Jul 03, 2007 5:39 pm

just park it behind an F-111 doing a dump and burn and it'll be back to bare metal in no time! LOL

VR4JA · Post by **VR4JA** » Tue Jul 03, 2007 5:44 pm

i hate paint stripper with a passion i feel for ya mate have ya tried those rough wire brushes u whack onto ya angle grinder :P makes short work of paint bog rust tires rims n anything else stuck to the side of ya starion rofl
i used stripper on me bonnet and face haha after that i threw the shit over the fence....

igottasicjb · Post by **igottasicjb** » Tue Jul 03, 2007 8:27 pm

i'm using wire brushes on my die grinder and angle grinder for removing seam sealant and a few bits of bog but all it does is smear the paint over the metal. I would never use one on a pannel it would have the same effect as shot peening and actually stretch the metal, which is great if you want a wave finish on the pannel.
but like you said...... bog, sealant and those anoying little stripped out plastic clips that are hard to remove wire wheels are great.

rofl parking it behind a f-111 are you sure the heat won't warp the pannel???

reminds me of the high octane overboost DVD, were they chain an old escort behind that jet drag car rofl rofl

thats about all there good for rofl

redzone · Post by **redzone** » Wed Jul 04, 2007 5:49 pm

^^^ hey i never said anything about it still being straight, just that it would be an effective way of removing paint!

best way i've ever seen of removing paint from a project car is redi-strip in victoria, basically a big tank that u sit the bare shell in, dissolves anything and everything thats not steel, so u gotta make sure its BARE! then they dip it in a neutralising tank, then wash it down, then dip it in a big tank of anti-rust solution..

hey presto "new" shell...

igottasicjb · Post by **igottasicjb** » Wed Jul 04, 2007 8:55 pm

would be nice if they were in brissi. it would make stripping it so easy,
i've seen electro priming done on a DVD and that would be a good way to prim all the internal pannels etc..

its like electroplating but they use primer......oh to have an endless bank acount :drool:

enthuzed · Post by **enthuzed** » Fri Aug 10, 2007 12:07 am

Is this the one you're restoring using the rear quarter and door from the one you just cut up?

igottasicjb · Post by **igottasicjb** » Fri Aug 10, 2007 1:29 am

yes it is. why do you ask?

igottasicjb · Post by **igottasicjb** » Fri Aug 10, 2007 1:43 am

Unfortunately when I first bought the car about 4 years ago it was dead straight, had a few engine probs that took about 6 weeks to sort out, 2 days after getting it running sweet I parked it outside IGA and went inside to get some food. Came back about 10-15 min later and someone had hit the driver’s door and the whole 1/4 panel with what looks like a tray back Ute. Needless to say the left no note and pissed off.
Rather than pull it all out and bog the thing I’m getting my panel shop to unstitch the panel and spot-weld the donor one on.

enthuzed · Post by **enthuzed** » Sun Aug 12, 2007 7:40 pm

igottasicjb wrote:yes it is. why do you ask?

Do you still have the passenger side rear quarter?
I've got a mate who wants that section, though shipping it from Bris to Melb might be prohibitive.

If you have it, is it up for sale? This will save him butchering a good whole shell.

igottasicjb · Post by **igottasicjb** » Sun Aug 12, 2007 11:54 pm

sorry mate the left hand 1/4 has already been sold.

there isn't much left on the the car that can be saved, its going to to scrap metal.

Austarion

pics of my jb 50% back to bare metal

pics of my jb 50% back to bare metal

ohmygod

Who is online