Got Dish? new pics page 5

Display your ride and post power figures, dyno runs, drag and circuit times.
Post Reply
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

definitely can go for more postive offset on the rear wheels. There is 155mm clearance from hub face to strut. I had 9" wide wheels with +38 offset and they just cleared.

They will look great either way. :beer
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

NXTIME wrote:definitely can go for more postive offset on the rear wheels. There is 155mm clearance from hub face to strut. I had 9" wide wheels with +38 offset and they just cleared.

They will look great either way. :beer
There is maybe 8-9mm between the wheel and the coil over as it is....

9" +38, what with adaptors/spacers?????

Factory is +18, I would say +12 is the limit for 10s, which would mean +24 for 9s.

Phil
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

They were Simmons and didn't have a stamped offset, but I calculated it to be about +35-38mm. It had 245's on it and there was easily 40-50mm left inside the rear guards. No spacers or adapter were used on the rear. 10mm spacers were used on the front. Front has 130mm from hub face to strut..

18 x 11's (on a widey) have a backspacing of 155mm and they have a bit of room left - at least 10mm.

Awaiting pics of your tyres and wheels all fitted. Will look tough.
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
Top
WHOD1N1
Dorifto!
Posts: 60
Joined: Sat Jun 17, 2006 1:49 pm
Location: Adelaide

Post by WHOD1N1 »

You would at least have to have your guards rolled. Also dont forget that the 19inch tyre is actually bigger than 18's or 17's even though you are going lower profile.
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

WHOD1N1 wrote:You would at least have to have your guards rolled. Also dont forget that the 19inch tyre is actually bigger than 18's or 17's even though you are going lower profile.
No not really.

Stock size = 195/70 14 = 628.6mm

235/45 17 = 643.3mm

225/40 18 = 637.2mm

265/35 18 = 642.7mm

225/35 19 = 640.1mm

265/30 19 = 641.6mm

305/25 19 = 635.10mm

They are still legal. I reckon I could fit a 305 but it's illegal, I can only go 50mm wider than orginal largest size. :(

Phil
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
WHOD1N1
Dorifto!
Posts: 60
Joined: Sat Jun 17, 2006 1:49 pm
Location: Adelaide

Post by WHOD1N1 »

Believe me they will be bigger, but will look good as it will fill up your guards.
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

They are actually smaller in rolling diameter than my old FR18s (see pic below).

Phil
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
WHOD1N1
Dorifto!
Posts: 60
Joined: Sat Jun 17, 2006 1:49 pm
Location: Adelaide

Post by WHOD1N1 »

Eaither way will look good. post pics once the tyres are on plz.

thanks
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

WHOD1N1 wrote:Eaither way will look good. post pics once the tyres are on plz.

thanks
No, thank you. :):):)

I can't wait for my tyres on Monday now!

Phil
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

Plenty of dish here ;)
Image
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
Top
ProZac
G33Kz0r
Posts: 2674
Joined: Thu Nov 27, 2003 1:26 pm
Location: Christchurch, New Zealand
Contact:
Contact ProZac

Post by ProZac »

Oi, phil, pics of em on the car. Now.

: D
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

Tyres.................

Monday. :)

Phil
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
User avatar
DD Phil
Enthusiast
Posts: 509
Joined: Wed Feb 18, 2004 8:17 am
Contact:
Contact DD Phil

Post by DD Phil »

NXTIME wrote:Plenty of dish here ;)
Image
Pffffffffffft 18s. :)

Phil
Last edited by DD Phil on Mon Aug 07, 2006 8:05 am, edited 1 time in total.
Image
Purple JA, full cage, 6G72TT, collecting dust
White JA, 19x10s, GT30, Alcons, DMS, Crower 2.4, Hypertune intake, M800.....
Top
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

157mm of dish on the rear, 130mm on the fronts :D
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

what? really? thats pretty chunky :)
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
Post Reply

Return to “Show And Go”

Who is online

Users browsing this forum: No registered users and 17 guests