Took out my banana-shaped strut out this afternoon and swapped the spring on to a spare, straight one. Putting the darned thing back in however... If i put the top in first and and the 3 bolts on loosely, I can get the bottom of the strut _almost_ into the axle housing, but not quite, the strut is still on to much of an angle and wont slip in. If i insert the strut into the axle housing first, I cant get the studs on the top to line up with the top of the wheel arch.. They seem to sit towards the rear of the car a little to far.
Can anyone help me please?
Re-installing rear struts
-
Starion_Turbo
- Enthusiast king
- Posts: 898
- Joined: Wed Dec 08, 2004 5:32 pm
- Location: South Australia
- Contact:
ok
first, either have someone stand on the suspension arm to bring it down or wedge a jack in-between the chassis and the arm to pull it as far down as possible, with the strut in arch insert it into base, you may need to pivot the hub to get it in, now allow the hub to lever towards the 3 strut top mounts, it should pivot enough on the arm.
Once this is achived let the arm back up slowley and align the top 3 bolts with the holes, its not an easy task but with enough fiddling and a bit of force, its entireley doable even by ones self.
first, either have someone stand on the suspension arm to bring it down or wedge a jack in-between the chassis and the arm to pull it as far down as possible, with the strut in arch insert it into base, you may need to pivot the hub to get it in, now allow the hub to lever towards the 3 strut top mounts, it should pivot enough on the arm.
Once this is achived let the arm back up slowley and align the top 3 bolts with the holes, its not an easy task but with enough fiddling and a bit of force, its entireley doable even by ones self.
Powerplant: Chipped stock ECU, 2044cc, 8.5:1, head intake enlarged and polished, exhaust manifold enlarged,
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Set the strut in the hub then line up the inner most thread on the strut top into its hole first then slowly jack the hub up and at the same time kinda guide/push the strut home. It IS fiddly - just be patient and work towards lining it all up and it'll come together
Never argue with an idiot, it brings you down to their level and they beat you with experience.
pro, shiftlock and i did his last weekend and it was heaps easier putting the top in first, we tried bottom in first and it was very diffifcult...
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
-
ProZac
- G33Kz0r
- Posts: 2674
- Joined: Thu Nov 27, 2003 1:26 pm
- Location: Christchurch, New Zealand
- Contact:
In the end the top went in first, then loosened off the axel housing pivot bolt so it could pivot easier and muscled it until it was a straight shot with the bottom of the strut :).
Man, jobs are much easier when you've got a clear head and aren't all foggy from work all day :).
Cheers for the replies guys!
Man, jobs are much easier when you've got a clear head and aren't all foggy from work all day :).
Cheers for the replies guys!
Who is online
Users browsing this forum: No registered users and 21 guests