FS: Engine parts + misc Starion bits
- Will
- Mine is bigger than yours
- Posts: 333
- Joined: Sun Jan 11, 2004 10:30 am
- Location: Sydney
- Contact:
FS: Engine parts + misc Starion bits
I found I still had some Starion parts and no Starion. I'm sure I'm not the first. Here's what I have:
1 x Starion block, oil squirts, crank, sump, dipstick (no rods, no pistons, no main caps) ($50)
2 x Engine mounts ($20 the set)
1 x SOHC head with cam,rockers,valves. I think one of the spark plug holes had a helicoil that has come out. ($20)
1 x rear anti-roll bar ($10)
1 x flywheel ($20)
1 x partial gasket kit, new, see post below($offers)
1 x knock sensor (sold)
1 x rocker cover in good condition ($30)
1 x steering box, works but would benefit from a rebuild ($20)
1 x Starion tow bar without tow ball, not sure where that went to ($0)
1 x DOHC head + manifold, see post below.
I'm open to any reasonable offers, especially if you pickup a few parts and make it easy for me :). Prefer pickup in Sydney North. PM me if you want any of the parts. Shipping is extra, and I'm only willing to ship the lightweight small stuff.
1 x Starion block, oil squirts, crank, sump, dipstick (no rods, no pistons, no main caps) ($50)
2 x Engine mounts ($20 the set)
1 x SOHC head with cam,rockers,valves. I think one of the spark plug holes had a helicoil that has come out. ($20)
1 x rear anti-roll bar ($10)
1 x flywheel ($20)
1 x partial gasket kit, new, see post below($offers)
1 x knock sensor (sold)
1 x rocker cover in good condition ($30)
1 x steering box, works but would benefit from a rebuild ($20)
1 x Starion tow bar without tow ball, not sure where that went to ($0)
1 x DOHC head + manifold, see post below.
I'm open to any reasonable offers, especially if you pickup a few parts and make it easy for me :). Prefer pickup in Sydney North. PM me if you want any of the parts. Shipping is extra, and I'm only willing to ship the lightweight small stuff.
Last edited by Will on Fri Jun 30, 2006 10:19 am, edited 3 times in total.
- Will
- Mine is bigger than yours
- Posts: 333
- Joined: Sun Jan 11, 2004 10:30 am
- Location: Sydney
- Contact:
Here's a pic of all the gaskets laid out. What I thought were valve stem seals are in fact something else. There's only 4 of them which look like mini valve stem seals. Must be seals for jet valves maybe? Because of this, I'll drop the price substantially. Just send me a PM.
Looks like this kit is designed to fit a few variants of the 4G63 (incl. Hyundai) and 4G62.
Looks like this kit is designed to fit a few variants of the 4G63 (incl. Hyundai) and 4G62.
-
- G33Kz0r
- Posts: 2674
- Joined: Thu Nov 27, 2003 1:26 pm
- Location: Christchurch, New Zealand
- Contact:
Do you rekon you'd split that set and sell a couple of little bits by themselves? Particularly the top left item (little rubber seal) and the bottom right item (gasket for MPI galant manifold).Will wrote:Here's a pic of all the gaskets laid out. What I thought were valve stem seals are in fact something else. There's only 4 of them which look like mini valve stem seals. Must be seals for jet valves maybe? Because of this, I'll drop the price substantially. Just send me a PM.
Looks like this kit is designed to fit a few variants of the 4G63 (incl. Hyundai) and 4G62.
Go on, no one else is gonna want em ;)
- Will
- Mine is bigger than yours
- Posts: 333
- Joined: Sun Jan 11, 2004 10:30 am
- Location: Sydney
- Contact:
Make me an offer I can't refuse :D
Are you really in Dubai? I was going to say, that if you pick them up, you can have them. If you pay for shipping, I'll ship them. PM me to make arrangements.
I forgot to add that I also have a 4G63 DOHC head + inlet manifold for sale. Head is off my VR4. Needs a skim because I removed it when it blew a headgasket (previous engine builder didn't clean the head and gasket enough before assembling. Some foreign matter got between the head & gasket :glare: ). Valve seats are cut for 1mm oversize valves. One of the exhaust studs has stripped. Inlet is ported and matched to the inlet manifold. Make an offer.
Edit: DOHC back on the market. Make a silly offer and it'll be yours.
Are you really in Dubai? I was going to say, that if you pick them up, you can have them. If you pay for shipping, I'll ship them. PM me to make arrangements.
I forgot to add that I also have a 4G63 DOHC head + inlet manifold for sale. Head is off my VR4. Needs a skim because I removed it when it blew a headgasket (previous engine builder didn't clean the head and gasket enough before assembling. Some foreign matter got between the head & gasket :glare: ). Valve seats are cut for 1mm oversize valves. One of the exhaust studs has stripped. Inlet is ported and matched to the inlet manifold. Make an offer.
Edit: DOHC back on the market. Make a silly offer and it'll be yours.
- Will
- Mine is bigger than yours
- Posts: 333
- Joined: Sun Jan 11, 2004 10:30 am
- Location: Sydney
- Contact:
VR4 Inlet manifold sold.
I have also a Starion TC-06. Seals are OK, front compressor wheel has some damage from some foreign object entering the intake. Still produces boost up to 10psi fine. Would suit some that has a good compressor wheel or wants to make a hi flowed TC-06 with new wheel. Looking for about $100.
Prefer pickup in Sydney. I'll post pics shortly.
I have also a Starion TC-06. Seals are OK, front compressor wheel has some damage from some foreign object entering the intake. Still produces boost up to 10psi fine. Would suit some that has a good compressor wheel or wants to make a hi flowed TC-06 with new wheel. Looking for about $100.
Prefer pickup in Sydney. I'll post pics shortly.
Who is online
Users browsing this forum: No registered users and 2 guests