Surge Tank Setup Including Hoses/Fittings $300
Surge Tank Setup Including Hoses/Fittings $300
Bosch 910 pump + lifter + surge tank, should supply well enough for 400hp
Tank/pumps cost $450 new, with hoses and fittings your looking at ~$600
$300 takes it
http://www.starlyon.com/pics/fs/IMG_1527s.JPG
Tank/pumps cost $450 new, with hoses and fittings your looking at ~$600
$300 takes it
http://www.starlyon.com/pics/fs/IMG_1527s.JPG
- madeofmilo
- Enthusiast
- Posts: 578
- Joined: Fri May 21, 2004 5:53 pm
- Location: Melb - East
not allowing that stuff to be shipped to my house is the ahittest thing ever!
i dont care if the jihads want to blow shit up i want to go faster!!
i would take it right now if it could be posted down here :glare:
i dont care if the jihads want to blow shit up i want to go faster!!
i would take it right now if it could be posted down here :glare:
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
- jakobsladderz
- Mine is bigger than yours
- Posts: 286
- Joined: Wed Feb 11, 2004 10:32 pm
- Location: Ballarat
put end caps on the pump and maybe get some blanking caps for the tank and others? Even when they're delivered new the bosch pumps have some test fluid in them.. If you really want to flush the petrol out, use some low odour kerosene or low odour turps. Perfectly safe for the pump and Aus post would be less worried too.
Trispen - A form of intelligent grass. It grows a single, tough stalk and makes its home on lawns. When it sees the lawnmower coming it lies down and pops up again after it has gone by. (Douglas Adams, The Meaning of Liff)
JA Starion - Mechanic's Training and on-road EFI testing laboratory.
JA Starion - Mechanic's Training and on-road EFI testing laboratory.
- Starion VR4
- almost postwhore
- Posts: 1293
- Joined: Fri Jan 09, 2004 5:08 pm
- Location: Brisbane
pm sent
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
you said it flav :D :D :D
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Who is online
Users browsing this forum: No registered users and 22 guests