Headunit setup.....

Ice Starion · Post by **Ice Starion** » Tue Mar 16, 2004 1:34 pm

Before:

After:

Camotec · Post by **Camotec** » Tue Mar 16, 2004 2:20 pm

well done man, looks very nice and suprisingly stockish

tmz_99 · Post by **tmz_99** » Tue Mar 16, 2004 2:25 pm

and the hair gel is still there.. :D :D

hmm, yeah, looks pretty nice.. :)

scum · Post by **scum** » Tue Mar 16, 2004 4:39 pm

looks cool, its been that long since I have seen my stereo and console I cant even remember what colour it is!

btw, just on a quite note, when you put the dash back together you do realise you put it the wrong way around, might want to sort that out.
:D

Camotec · Post by **Camotec** » Tue Mar 16, 2004 6:26 pm

btw, just on a quite note, when you put the dash back together you do realise you put it the wrong way around, might want to sort that out.

Hehe :beer

Ice Starion · Post by **Ice Starion** » Wed Mar 17, 2004 2:09 pm

scum wrote:btw, just on a quite note, when you put the dash back together you do realise you put it the wrong way around, might want to sort that out.
:D

damn iam slow

i dint´no know what the hell u where talking about but that was a good one :beer

merlin · Post by **merlin** » Wed Mar 17, 2004 9:28 pm

carbon fibre look is good, weighs less too!

Camotec · Post by **Camotec** » Wed Mar 17, 2004 9:37 pm

hey merlin do you know where to buy carbon fibre that is already resign into flat hard sheets??

I can only get the raw fabric and then i would have to do the resin myself and am trying to avoid it because i have never done it before. but if it has to happen then it will i guess.

Hey ICESTARION,
Does your gear knob have buttons on it?? if so what do they do?

Cheers

Ice Starion · Post by **Ice Starion** » Thu Mar 18, 2004 4:23 am

merlin wrote:carbon fibre look is good, weighs less too!

i realy do´nt like it

Ice Starion · Post by **Ice Starion** » Thu Mar 18, 2004 4:26 am

Camotec wrote:Hey ICESTARION,
Does your gear knob have buttons on it?? if so what do they do?

yes those are buttons but they are broken but thay could have bean used for any thing like neons, roll control or nos but iam just looking into getting a stock one or a stockish one

androoz · Post by **androoz** » Tue May 04, 2004 1:04 am

im currently working on my car audio.. gotta cut the top piece of plastic though.. stock plastic paint is peeling off though.. so gotta spray that black.. :?

another problem i had was, when i attached the stereo brackets (side ones), they sit wider than the stock stereo.. my solution, i used my hammer to bang in the mounts which makes the brackets sit wider.. it probably wasnt a good idea to do that, but i had no other choice..

how did everyone else get over this.. if you even understand what i just typped.. :o

Camotec · Post by **Camotec** » Tue May 04, 2004 11:10 am

I think the hammer is the most used tool on a starion apart from the usual size spanners and screwdrivers :D

Chris 83JA · Post by **Chris 83JA** » Tue May 04, 2004 12:19 pm

I've upgraded to a sledge hammer for most starion work, sems to work a bit better

Austarion

Headunit setup.....

..

Who is online