intercooler piping...

[strion]

does anyone have coola pipes for tc06 turbo and L300 manifold?
how much???
0403562860 sydney

[strion]

ok bad question...
so how much should i look at spending???
wats a good price range???

[Barney]

do it your self with exhaust bends and silicon hose

ASHLY

[Cookiemonster]

Yep do it yourself. About $15 per 90 degree bend.

Line up and cut the pipe yourself.

Then add $70-$100 to get it all welded up.

Add $150-$200 for some silicon joiners and clamps and your done.

[dirtysanchez]

I have an intercooler for sale, together with stainless steel intercooler piping to suit a TC 06 and standard throttle body. Also includes blowoff valve. Should only need very minor mods to suit L300. Asking $500. If you give me your email address I will send you photos.

[strion]

ive already got a nice sized intercoola man thanx any ways...
i could get the bend from any exhaust shop right?

[Cookiemonster]

i could get the bend from any exhaust shop right?

You should be able to. Liverpool Exhausts have them.

[WANTSOM]

Or come round my place - I still have 4 or 5 bends (2 and quarter inch) left over mild stel - $10.00 each. They come in both left and right hand designs :D

And I'm round the corner.

Cheers
Greg

[strion]

Greg do you have enough piping for the whole job?
if so when can i come to get it, i mean whenever your free.
my number is 0403562860 so if you want call me and let me know
if youve got enough for the whole job and when i can come pick it up.
thanks guys...

[strion]

the guy at livo exhaust said i should get 5 90 deg bends and 5 45 deg bends...do u really need that many???
wats a good size to get them in. 2 inch or 2 1/2 inch???
im gonna go there today n hopefully work something out.

[Cookiemonster]

What size are the inlet and outlet pipes on your intercooler? Get piping to match this if possible.

[strion]

the inlet n outlet are both roughly 2 inch....
how many of each bend would i need...90 deg and 45 deg???

[StarionChef]

Tell us exactly what you have, what way the turbo outlet points, what manifold and TB, and where are the inlet/outlets of the cooler sitting.

On mine I used 5 90's and 1 180, 2in from turbo to cooler, 2 1/2 from cooler to standard JB TB. yours should be the same

[strion]

well i went to livo exhaust and found that the bends are real tiny, i thought they would be alot bigger...
turbos facing the tb...
with these bends itll still cost a fair bit to do it.
wantsom how big are your pipes?
i got quoted 500$$ for the intercooler mounted and the plumbing from a performance shop but i was thinking for them to just mount and weld the pipes

[StarionChef]

Its easy to make the brackets to mount the cooler yourself, rotate the compressor housing so it faces 9oclock, run a 90deg 2in bend off that, into a straight, through rad' suport panel, a 90 deg bend into the cooler (depending on where the inlet is) Out of the cooler witha 90deg bend, therough the rad suport, allong the chassis rail into a 90deg bend and take it up to the TB then into a 180deg bend and into the TB.

should only cost a few hundred if you buy the bends and straight pipe, measure , cut yourself then take them back to the shop and have them weld them for you.
Hoses and clamps will bump the price up maybe 50 tops

Im asuming you can cut the pipe at home, if you need help we arent far away