REAR Camber Adjusters N-E-1 Interested ? UPDATED PHOTO

Oscar-the-Grouch · Post by **Oscar-the-Grouch** » Sat Dec 03, 2005 6:55 am

G'day mates

(Sorry that was a poor attempt from a Cuban living Stateside to fit in, but I try ) :D

Anyhow....
I am currently making these in a large production run so I could drive the price DOWN and offer more features and still keep the price the same as before. And I have done so.

The REAR set of Camber Plates (Or Strut Plates as you may know them) will be made from steel vs the original design in Aluminum (A bit more strength for those of you looking for something TOUGH) Also the fastners/hardware will be grade 5 Stainless Steel vs the original steel and nickle. And finally the plates will be Powder coated BLACK for a nice finished look.

The Photo bellow is of the original prototypes in Aluminum and with standard steel fastners so the one for sale NOW will look the SAME as far as design and dimmentions but will have the new features mentioned above.

These Rear Camber Plates are compatible wsith BOTH Original suspenssion and Coil Overs. So its UNIVERSAL for the Starion and ALL models and years and best of all NO MODIFICATIONS are needed, just replace your original strut TOPS with these and re-assemble the assembly and you are good to go. So AGAIN these are BOLT-ON.

More info on these camber plates can be found at the LINK bellow, and remember these REAR Camber Plates are the ONLY ONES available out there for ANYWERE NEAR this price. The next closest one is over USD$200.00 and they are NOT BOLT-ON like these are. And YES they WILL work with either Coil overs AND OEM Springs, the others CANNOT make that claim. So these are one of a kind and for the price... well you know... well worth it

http://www.antimpower.com/misc/camberplateguide.htm

Now as far as PRICE.
The Complete set of TWO with ALL hardware as pictured above (But in Steel and powdercoated) will be USD$85.00/AUD$120.00 (Please check exchange rates for more up to date rates) and INCLUDES Air Mail posting to you in Australia or New Zealand. (4-10 days delivery to your door)

Pay-pal Payment info:

CASH
If you are sending instant cash or from your pay-pal account balance through paypal, then send it to:
oscar-the-grouch@sbcglobal.net
NO CREDIT CARDS OR ATM/DEBIT CARDS to this account please.

CREDIT/DEBIT CARDS
If you are using a CREDIT CARD through paypal send payment to:
oscardortega@yahoo.com
PLEASE add AUD$3.00 to your order if you will be using a CC to cover fees.

Pay-pal IS preffered.
Any questions PLEASE dont hessitate to ask.
Post here or E-mail me for details.

Cheers
Oscar

Cookiemonster · Post by **Cookiemonster** » Sat Dec 03, 2005 7:15 am

No piccie... :(

How much for some aluminium ones Oscar?

Oscar-the-Grouch · Post by **Oscar-the-Grouch** » Sat Dec 03, 2005 9:07 am

Cookiemonster wrote:No piccie... :(

How much for some aluminium ones Oscar?

Man Cookie...!
Are you just sitting in front of the computer waiting for a post to look at ?
Must be nice huh ? :D

Anyhow...
I ONLY have TWO left in Aluminum for the ORIGINAL struts and THREE to use with Adjustable Aftermarket Struts with the thicker Shaft. (This option is more likely for us here in the US)

Price IS the same for either STEEL or Aluminum but the NEW ONES will be STEEL as to increase rigidity and longivity concerns by some members.

Oscar

CussCuss · Post by **CussCuss** » Sat Dec 03, 2005 6:29 pm

yeah why not, im in, only a hundred bux

Cookiemonster · Post by **Cookiemonster** » Sat Dec 03, 2005 9:03 pm

Oscar, I'll have a set of aluminium ones suitable for aftermarket shocks with the larger shafts.

PM me payment details and I'll send you my address.

Oscar-the-Grouch · Post by **Oscar-the-Grouch** » Sun Dec 04, 2005 11:13 am

Cookie:
I have posted the payment info on the first post for all to see and have available. Pay-pal is preffered as its faster and safer for all.

Also Cookie I just wnat to make sure you get what you need so I am looking for the dimmentions of the center slider hole for the aftermarket shocks to make sure they will work with yours. But beeing aluminum they can easily be grinded open a bit more woth little effort. But in any case I want to make sure of the demmentions before I sell you somethign that will not fit .

Do you have the OD of the threaded part of the shocks YOU have now ?
Thanks again mates

Oscar

Cookiemonster · Post by **Cookiemonster** » Sun Dec 04, 2005 11:38 am

Oscar-the-Grouch wrote:I have posted the payment info on the first post for all to see and have available. Pay-pal is preffered as its faster and safer for all.

Is oscardortega@yahoo.com your paypal address?

Oscar-the-Grouch wrote:Also Cookie I just wnat to make sure you get what you need so I am looking for the dimmentions of the center slider hole for the aftermarket shocks to make sure they will work with yours. But beeing aluminum they can easily be grinded open a bit more woth little effort. But in any case I want to make sure of the demmentions before I sell you somethign that will not fit .

Do you have the OD of the threaded part of the shocks YOU have now ?
Thanks again mates

Oscar

OD is 15mm. If this size works I'll paypal some money on over to you.

Oscar-the-Grouch · Post by **Oscar-the-Grouch** » Sun Dec 04, 2005 12:16 pm

Cookie

Yes thats the one for CC payments ONLY.
And I am still looking for those measurements. I have them on a CAD document and my MAC at home cannot access the info so I have to either find a PC or wait till monday to access the info from Work. I will let youknow as soon as I find them.

Sorry mate
Oscar

Cookiemonster · Post by **Cookiemonster** » Sun Dec 04, 2005 12:30 pm

Thanks Oscar.

CussCuss · Post by **CussCuss** » Sun Dec 04, 2005 2:12 pm

payment sent

flav · Post by **flav** » Mon Dec 05, 2005 12:00 pm

Nice chap that Oscar Bloke!
Pat pat.... :D

JJH · Post by **JJH** » Tue Dec 06, 2005 9:53 am

Can't see the picture Oscar, or follow the link, is it just me??

If the steel is TOUGH, how whimpy is the aluminium and what is the weight difference? :?

Which one would better suit a car that will do mainly circuit events PLUS the odd road (bitumen) rally like Mt Buller Sprint, East Coast Rally etc.?
Cookie, Flav, anyone else, your 2 pennies worth?

I'd give a clear yes or no if I could see the picture

Sounds good though Oscar.

Oscar-the-Grouch · Post by **Oscar-the-Grouch** » Tue Dec 06, 2005 10:51 am

JJH

I guess you need a new puter mate ! =)
Just checked and loaded this page and the link with both a Mac and a PC"shit" and both loaded fine.

I will try e-mailing you the link and the pic NOW.
And PERSONALLY I will go with Steel just for the added peace of mind. And I personally dont mind the extra 1lb of weight these will add over the aluminum BUT they will be about the same weight as the Original Stru tops you have from factory. So pound for pound they will be same as the originals if you go Steel.

Thansk
Oscar

Cookiemonster · Post by **Cookiemonster** » Tue Dec 06, 2005 5:49 pm

Any confirmation that they will fit my shocks, Oscar?

flav · Post by **flav** » Wed Dec 07, 2005 1:44 am

Don't these require sphericals on top?

Austarion

REAR Camber Adjusters N-E-1 Interested ? UPDATED PHOTO

REAR Camber Adjusters N-E-1 Interested ? UPDATED PHOTO

Who is online