Hydraulic lifter conversion

All technical questions and answers regarding starions, being modifications to maintenance.
Post Reply
User avatar
Jesusdroveawestfield
christian moderator
Posts: 180
Joined: Fri Jan 09, 2004 7:13 am

Hydraulic lifter conversion

Post by Jesusdroveawestfield »

I really like my Starion, like the engine, love the power it now puts out etc. But I HATE HATE HATE the amount of tappet noise that these engine put out. Years ago I had a Magna with hydraulic tappets. I remember changing the tappets in it and they were just s kind of insert. Could the rocker arms be the same ? or converted to suit. What would be the disadvantage of hydraulic tappets.
I wouldnt want to belong to any club that would have me as a member
User avatar
Cookiemonster
Mother Goose
Posts: 3177
Joined: Thu Jan 08, 2004 4:33 pm
Location: Sydney

Post by Cookiemonster »

Yes, on most occasions hydraulic lifters are quieter than mechanical tappet lifters since there is no lash or free-play.

But they generally fall short of offering optimum performance above 6,000 - 6,500 RPM. And many cheaper designs fall even shorter than this. This poor performance at high RPM is due mainly to the inability of the lifter to "bleed down" the excessive oil pressure, and thus does not allow the valves to seat.

Hydraulic lifters can also be just as noisy as well.. my Pajero has hydraulic lifts and the tappet noise from that is a lot more than the lifters in my Staz. Maybe I should replace them.
User avatar
Alspos
Flucking kwankers
Posts: 4107
Joined: Thu Jan 08, 2004 2:09 pm
Location: Melbourne
Contact:

Post by Alspos »

They need to be pulled out and re-oiled or whatever they call it. There's air in them. US sites have plenty of info on how to do it.
User avatar
Jesusdroveawestfield
christian moderator
Posts: 180
Joined: Fri Jan 09, 2004 7:13 am

Thanks

Post by Jesusdroveawestfield »

But will they fit Starion rocker arms or do you replace the entire arm ? Anybody got both they can compare ?
I wouldnt want to belong to any club that would have me as a member
User avatar
Cookiemonster
Mother Goose
Posts: 3177
Joined: Thu Jan 08, 2004 4:33 pm
Location: Sydney

Post by Cookiemonster »

You'd have to replace all the arms. Would they fit though? Would they clear the valve cover? Which ones would you use?
User avatar
Jesusdroveawestfield
christian moderator
Posts: 180
Joined: Fri Jan 09, 2004 7:13 am

Arms

Post by Jesusdroveawestfield »

I guess the easiest way would be to get some from pick and payless and see if the general arm is the same ?
I wouldnt want to belong to any club that would have me as a member
MrBishi
nearly postwhore
Posts: 1683
Joined: Fri Jan 09, 2004 9:11 am
Location: Seoul

Post by MrBishi »

There are a few problems I can think of;
-Cam profiles are different.
-Extra oiling holes in the rocker shafts.
-The magnas had a larger oil pump to keep the hydros pumped up.

This is coming from the perspective of fitting hydraulic tappets to a non hydraulic head in the sigma/magna range.

Did any of the 2.4L Sirius motors (Hyundai or Mitsu) have hydraulics??
4G63 - 87kg
4G54 - 107kg
User avatar
Starion VR4
almost postwhore
Posts: 1293
Joined: Fri Jan 09, 2004 5:08 pm
Location: Brisbane

Hyd Tappets

Post by Starion VR4 »

Cam profiles are different.
-Extra oiling holes in the rocker shafts.
all correct, the main noise that is heard is most likely the rockers and rocker shafts, with 100,000 km's on them these items were the most over looked items on rebuild. This of course is after you have ground the cam and re-radiused the rocker pads..look into new shafts and rockers, you will be suprised at the difference in total engine noise. :smokin
Post Note, YES the cam lobe profiles are different solid- Hydraulic, the opening/closing ramp, the rate of lift and duration as well as gross lift is different, as quoted below,it will not run correctly.
Last edited by Starion VR4 on Mon Mar 01, 2004 8:40 pm, edited 1 time in total.
Image

30PSI,2.4L! Wolf 3D Ver 4. VR4 Head.
User avatar
Jesusdroveawestfield
christian moderator
Posts: 180
Joined: Fri Jan 09, 2004 7:13 am

good points

Post by Jesusdroveawestfield »

my car only has 87,000 ks but you may be right.
I wouldnt want to belong to any club that would have me as a member
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

I tried a hydraulic set up years ago when I rebuilt my first engine. They will not work correctly with a standard cam. I can't recall exactly why, but a few things were tried before we went back to adjustables. I am sure that the lifter were the same as 2.6 Magna ones.
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
ProZac
G33Kz0r
Posts: 2674
Joined: Thu Nov 27, 2003 1:26 pm
Location: Christchurch, New Zealand
Contact:

Post by ProZac »

You should be able to eliminate pretty much all of the noise by adjusting the valve clearances? Just make sure you do it hot... took me a couple of tries, by i had my engine idling very quietly :)
quest
I love starions
Posts: 411
Joined: Fri Jan 09, 2004 7:42 pm

Post by quest »

any perf cam I've ever installed ran loose clearances, ~020 or so. Car ran poorly and affected performance if you tried closing it up.
.... or are u saying, even stock tappets (006/010) are noisy ?

pretty common for us 2.6 to exchange stock hyd for adj from minivan.
The 2.6 can run the 2.0 cam, so other stuff 'might' fit.
Perf cam spec different cams for hyd vs mech
User avatar
SpidersWeb
postwhore!
Posts: 1984
Joined: Wed Jan 28, 2004 2:29 am
Location: Wellington, NZ

Post by SpidersWeb »

133,000Km
1986 stock standard Starion GSR-III 8 valve Sirius JET

Only thing that has been changed on the motor is the cambelt at 96K. I have absolutely no noise besides the exhaust. My Galant taps a bit at high rpm when the oil is low.

Strange to hear of this being a problem.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
kiwistar
I like starions
Posts: 138
Joined: Mon Feb 16, 2004 3:16 pm
Location: Auckland

Post by kiwistar »

Pretty standard noise for SOHC mitsy motors.

Just listen to an old rwd lancer or galant next time one drives past.
User avatar
SpidersWeb
postwhore!
Posts: 1984
Joined: Wed Jan 28, 2004 2:29 am
Location: Wellington, NZ

Post by SpidersWeb »

My Staz doesn't make that noise at all

Idle, or revving, even with the bonnet up and standing next to the motor, there is no tapping noise.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
Post Reply

Who is online

Users browsing this forum: No registered users and 25 guests