2.6 makes outstanding power

quest · Post by **quest** » Mon Oct 10, 2005 6:38 am

Good ones popping up on the u.s. forums lately.

http://www.starquestclub.com/forums/vie ... php?t=8890
http://www.starquestclub.com/forums/vie ... c3ae5f7b96

400+ ft-lbs tq at the threads, on pump fuel is exceptionally strong.
460+ ft-lbs is nuts.
Most use your magna intake
Some even on 17 year old stock bottom end or non-ported head or stock camshaft even... amazing
A few old school full wt. widebodys already done low 11s 1/4. hot street car performance
Doesn't take a whole lot to make a 2.6 angry

mrb1 · Post by **mrb1** » Mon Oct 10, 2005 10:22 am

I hope to join the 2.6 300+ club soon

toysrus · Post by **toysrus** » Mon Oct 10, 2005 12:10 pm

The 300+ club is for softies :D

C'mon and try for the dark side - the 500Hp club

How big of an Exhaust Housing A/R can the 2.6L spool fine ? 0.86/89 or are we talking in the 1.0-1.10 ?

MrBishi · Post by **MrBishi** » Mon Oct 10, 2005 12:14 pm

toysrus wrote:
How big of an Exhaust Housing A/R can the 2.6L spool fine ? 0.86/89 or are we talking in the 1.0-1.10 ?

Big. I have a 1.06 TO4 exhaust and it spools at 2500ish rpm. The big cubes make up for lack of technology!

mrb1 · Post by **mrb1** » Mon Oct 10, 2005 12:32 pm

Yes I am runing a works Ralliart TD06-19C it has a 12cm2 turbine housing

logik · Post by **logik** » Mon Oct 10, 2005 12:38 pm

The big cubes make up for lack of technology!

i believe that kind of talk belongs in street commodores

YELLA TERRA SUPERCHARGER
YEA GOT THE INJECTED 351 CLEVELAND IN THE FALCUN

keep it out of here :D

Junkers · Post by **Junkers** » Mon Oct 10, 2005 4:22 pm

12cm2 !!!!!!!!! Isn't that a bit excessive? I noticed with the 2lt engine the 8cm2 housing of a TC06 would support around 5500-6000rpm

toysrus · Post by **toysrus** » Mon Oct 10, 2005 5:22 pm

mrb1 wrote:Yes I am runing a works Ralliart TD06-19C it has a 12cm2 turbine housing

Wanna compare it to a TD06H-25G with the 12cm^2 Housing ? :D

DD Phil · Post by **DD Phil** » Tue Oct 11, 2005 8:02 pm

toysrus wrote:The 300+ club is for softies :D

C'mon and try for the dark side - the 500Hp club

How big of an Exhaust Housing A/R can the 2.6L spool fine ? 0.86/89 or are we talking in the 1.0-1.10 ?

A 0.82 GT30 did fine on my 2lt when still stock.

Phil

quest · Post by **quest** » Wed Oct 12, 2005 3:54 am

300hp on the 2.6 not hard. MPI ?
The 2.6 got the lungs to spin up a big turbo, and they really come alive with high boost.
Most of the dynos are on the older T04b series - v-trim compressor/ 0-trim turbine quite common. 25-28psi does wonders.
The blue 10sec EIP quest on the video ran 11.3 on one, 10.4 spraying a 75 shot. stock 2.6 cam too! PUMP gas!! VERY impressive for a heavy arse 4cylinder car! Does NOT get any better than that for the input
Some 2 valve 1.8L (3TC) old school street toyota corollas run the exact turbo.... goes high 11s/mid 10s on pump
Who needs 4 valve heads ?

I plan to experiment with the mitsu 2L sohc in the same fashion, 20-24psi on a t3/t4. MPI & standalone obviously. Would be interesting to see where the limits are for; oe head gasket, pistons, head & cam. G54b big brother has certainly raised some eyebrows, so.....

mrb1 · Post by **mrb1** » Wed Oct 12, 2005 10:04 am

StazzyBabyYeah wrote:12cm2 !!!!!!!!! Isn't that a bit excessive? I noticed with the 2lt engine the 8cm2 housing of a TC06 would support around 5500-6000rpm

No way it's perfectly matched to the 2.6. Mitsubishi knew what they were doing with that one.

FuelinjectionPro · Post by **FuelinjectionPro** » Tue Nov 22, 2005 8:50 am

toysrus wrote:The 300+ club is for softies :D

C'mon and try for the dark side - the 500Hp club

How big of an Exhaust Housing A/R can the 2.6L spool fine ? 0.86/89 or are we talking in the 1.0-1.10 ?

The 500HP club is ready for members!! Join up!
http://www.starquestclub.com/forums/vie ... php?t=8890

Austarion

2.6 makes outstanding power

2.6 makes outstanding power

Who is online