STRUT BRACE ORDER INFO

grumbly · Post by **grumbly** » Tue Jun 21, 2005 11:21 am

Cost will be $165 front and $160 rear. This includes Australia wide shipping.

Pre orders will attract a $20 discount if paid in full.

Front and rear together will be $300, pre order $280

Payments to:
David Bilney
PO Box 40
Ingle Farm SA 5098

or deposit to:
ACC: 22390821
Name: DA & TJ Bilney
BSB:805-022
Reference: your username.

email confirmation to grumbly@adam.com.au
include username and delivery details.

All pre-payments before 21 July. This will enable me to order the bars asap and get delivery done hopefully end of July.

Cheers

Grumbly

Website · Post by **WidebodyWoody** » Tue Jun 21, 2005 12:19 pm

How long does production of one take? A couple of hours?

Fuel · Post by **Fuel** » Tue Jun 21, 2005 1:25 pm

Any pics?

grumbly · Post by **grumbly** » Tue Jun 21, 2005 3:53 pm

pics of prototype coming.
production of one? no idea. I am making 15 sets at once.

JD_Stazza_Brendan · Post by **JD_Stazza_Brendan** » Tue Jun 21, 2005 7:07 pm

Will this fit on a JD???

Starion_Turbo · Post by **Starion_Turbo** » Tue Jun 21, 2005 7:54 pm

should do I belive all starion shells were essentially the same, just check that it has a 3 bolt pattern on towers.

JD_Stazza_Brendan · Post by **JD_Stazza_Brendan** » Tue Jun 21, 2005 8:04 pm

Starion_Turbo wrote:should do I belive all starion shells were essentially the same, just check that it has a 3 bolt pattern on towers.

I should have made myself clearer,,,
Will it clear the intercooler piping setup on the JD

Starion_Turbo · Post by **Starion_Turbo** » Tue Jun 21, 2005 8:12 pm

does this piping sit higher than the throttle body??
we know it clears a vr4 conversion, but i dont think ive ever seen a factory set up JD intercooler and piping.

JD_Stazza_Brendan · Post by **JD_Stazza_Brendan** » Tue Jun 21, 2005 8:41 pm

sorry for hijacking thread, but here are 2 pics of my factory JD intercooler piping... will it clear

http://memimage.cardomain.net/member_im ... 4_full.jpg

http://memimage.cardomain.net/member_im ... 6_full.jpg

Starion_Turbo · Post by **Starion_Turbo** » Tue Jun 21, 2005 9:08 pm

yeah that should be fine it looks like it sits at the same hight of a standard crossover pipe and the first gen prototype bar cleared that, the test bar angled up slightly from the shock towers then leveled out.

Pictures of the prototype as fitted to a Starion would be a real asset in this department. . . . . . .

grumbly · Post by **grumbly** » Tue Jun 21, 2005 9:19 pm

Drive up to Blakeview and I'll fit the prototype, front and rear and take pics.
easy eh? :D

Starion_Turbo · Post by **Starion_Turbo** » Tue Jun 21, 2005 9:25 pm

just pm'd you about exactly that b4 I read this LOL

mrb1 · Post by **mrb1** » Tue Jun 21, 2005 10:39 pm

Will it fit over a L300 manifold?

Starion_Turbo · Post by **Starion_Turbo** » Wed Jun 22, 2005 8:17 am

good question, i'm hoping to go and test fit one on my stock starion for photos and take a few measurments to post up for this kind of help.

Website · Post by **WidebodyWoody** » Wed Jun 22, 2005 8:58 am

It should fit any standard starion, but I hope it still fits with the magna inlet. Otherwise I will have to make it fit

Austarion

STRUT BRACE ORDER INFO

STRUT BRACE ORDER INFO

JD

pics

Who is online