Dash removel and leather storage
Dash removel and leather storage
OK two questions for you starquest heads. ONE, how do I get the entire dash board assembly off? I have a quest that got wrecked because I let a friend drive it and I am tearing it completely apart. I took out everything from the dash back. All that’s left is the dash and the steering column. I took out every screw and bolt that I could find. Even had to drill two screws off because I could not get them out. It seams like there is locktight on ever screw in the car. TWO, how do you suggest that I store the interior pieces, it is a complete black leather interior in mint condition. I want to keep it that way, I am thinking wrapping each piece in cloth and then putting it in a black trash bag after washing treating with leather treatment and letting completely dry. Let me know what you think. Thanks for all the help. Brad
1989 Chrysler Conquest TSI Electric Blue wrecked, 1989 Chrysler conquest TSI R04 red RIP, 1989 Chrysler Conquest TSI Black and Tan MPI set up, 1988 Firebird Trans AM, 1987 Camaro Z28 IROC-Z, 1987 BMW 325is, 1978 Dodge RamCharger
14.133 @ 96.8 W/ 1.881 60ft
14.133 @ 96.8 W/ 1.881 60ft
You probably missed the bolts under the top vents "G" on each side in Al's picture. It should just come out once you remove them (and the two obvious ones "H" on each side) and all the stuff around the centre console and heater controls. The dash then slides out on two guides protruding from the top centre just under the clock.
- Sargeant_Khan
- Enthusiast
- Posts: 673
- Joined: Thu Dec 16, 2004 9:31 pm
- Location: Ipswich
- Sargeant_Khan
- Enthusiast
- Posts: 673
- Joined: Thu Dec 16, 2004 9:31 pm
- Location: Ipswich
- SpidersWeb
- postwhore!
- Posts: 1984
- Joined: Wed Jan 28, 2004 2:29 am
- Location: Wellington, NZ
It helps. But I didn't.
I removed the supports so the wheel and steering column fell down, then kinda managed to get the dash up and over the wheel.
The trickest part was the heater. I couldn't work it out, then had another look and it had fallen out. So Ive still got no idea the proper way of removing the face plate with the screws behind it.
At any rate, it will be easier if you remove the wheel, I didnt because at the time I did not have a steering wheel puller and wasnt strong enough to pull the wheel off the splines. So I just wrestled with it a little.
I removed the supports so the wheel and steering column fell down, then kinda managed to get the dash up and over the wheel.
The trickest part was the heater. I couldn't work it out, then had another look and it had fallen out. So Ive still got no idea the proper way of removing the face plate with the screws behind it.
At any rate, it will be easier if you remove the wheel, I didnt because at the time I did not have a steering wheel puller and wasnt strong enough to pull the wheel off the splines. So I just wrestled with it a little.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
- SpidersWeb
- postwhore!
- Posts: 1984
- Joined: Wed Jan 28, 2004 2:29 am
- Location: Wellington, NZ
na, I got a grey GSR-III in many pieces (goes to get melted in a week or so, still registered, but dont think anybody will want it), and a black GSR-X.
http://www.starion.co.nz/images/gsrx-jbump1.jpg <- quick pic for you
As for the wheel:
Steering wheel puller you can get from SuperCheap or Repco for cheap as. Makes the process less stressful. In the past Ive just had friends rip them out for me. Does take a bit of effort, and if you decide to do it, something soft on your chest helps. Otherwise you can get a fair whack when the wheel finally lets go. Unless its aftermarket and has the nice 6 allen key bolts, which makes it a 1 minute job.
http://www.starion.co.nz/images/gsrx-jbump1.jpg <- quick pic for you
As for the wheel:
Steering wheel puller you can get from SuperCheap or Repco for cheap as. Makes the process less stressful. In the past Ive just had friends rip them out for me. Does take a bit of effort, and if you decide to do it, something soft on your chest helps. Otherwise you can get a fair whack when the wheel finally lets go. Unless its aftermarket and has the nice 6 allen key bolts, which makes it a 1 minute job.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
- SpidersWeb
- postwhore!
- Posts: 1984
- Joined: Wed Jan 28, 2004 2:29 am
- Location: Wellington, NZ
Side vents can be kept if you want them. There is lots of other crap there too, including a cloth interior with perfect seats, that I dont want.HWYSTR wrote:hey what condition are your GSR-III's doors in !
of if they are rusty as can i get your locks and ignition.... ?
my car currently uses 3 keys,, 1 for each door and 1 for ignition + boot..
how about the GSR-III side vents ?
Its doors are on the GSR-X :) I too am doing the mutli-key things. Sorry cant help there hehe
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
Who is online
Users browsing this forum: No registered users and 56 guests