Knocksensor broke?
-
- [P] Plater austaz
- Posts: 20
- Joined: Wed Jun 23, 2004 4:26 am
- Contact:
Knocksensor broke?
Can anyone tell me what happens if the knocksensor brakes down or is disconected. will the engine spark control work well or will it work on emergency mode? or can it effect the coil/negative signal?
4g63 8 valve 1983 turbo engine.
Kind regards,
johan
4g63 8 valve 1983 turbo engine.
Kind regards,
johan
- Starion VR4
- almost postwhore
- Posts: 1293
- Joined: Fri Jan 09, 2004 5:08 pm
- Location: Brisbane
Knock senser
If your sensor is stuffed, it will not retard the timing when it does detonate, it doesn't have a safe or limp home mode, when it sensers detonation the control unit delays the firing of the ignition by 15ms? about 8deg. :beer
30PSI,2.4L! Wolf 3D Ver 4. VR4 Head.
Re: Knock senser
Well I'm not sure what it will do however 15mS is 540 degree at 6000 RPM so I don't think it will retard that much but yes I think 8 degrees.Starion VR4 wrote:If your sensor is stuffed, it will not retard the timing when it does detonate, it doesn't have a safe or limp home mode, when it sensers detonation the control unit delays the firing of the ignition by 15ms? about 8deg. :beer
But I think yes it will just not retard at all. It's the ignitor module that decides this the knock sensor wiring goes directly to the ignitor not to the ECU.
Last edited by mrb1 on Tue May 03, 2005 8:41 pm, edited 1 time in total.
- Starion_Turbo
- Enthusiast king
- Posts: 898
- Joined: Wed Dec 08, 2004 5:32 pm
- Location: South Australia
- Contact:
knock sensor, is this a bolt like part which goes into the side of the block and has a single wire coming out of it??
If not what is the part I just described?
If not what is the part I just described?
Powerplant: Chipped stock ECU, 2044cc, 8.5:1, head intake enlarged and polished, exhaust manifold enlarged,
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
- Cookiemonster
- Mother Goose
- Posts: 3177
- Joined: Thu Jan 08, 2004 4:33 pm
- Location: Sydney
- Starion_Turbo
- Enthusiast king
- Posts: 898
- Joined: Wed Dec 08, 2004 5:32 pm
- Location: South Australia
- Contact:
Well im in the shit then :(
When I replaced the head gasket months ago I didn't see that sensor connected and the wire was pulled completly out of the device :( I pushed it back in then used silicon (no garentee that its connecting) and resolved to get another one off a wrecked Starion at lonsdale (hour -> hour and half) drive away)
went there last week and the whole block had been taken :roll: so im still running on a questionable "knock sensor" BTW its a daily driver
What symptoms should I be experiencing?? (dont tell me about timing etc plz) I have noticed one in particular which happens rarley but would like some info to confirm.
were can I get another one?? ie: is there a replacment part still available?
dosnt sound like the kind of thing a wrecker would part with unless I bought the whole engine.
Cheers
When I replaced the head gasket months ago I didn't see that sensor connected and the wire was pulled completly out of the device :( I pushed it back in then used silicon (no garentee that its connecting) and resolved to get another one off a wrecked Starion at lonsdale (hour -> hour and half) drive away)
went there last week and the whole block had been taken :roll: so im still running on a questionable "knock sensor" BTW its a daily driver
What symptoms should I be experiencing?? (dont tell me about timing etc plz) I have noticed one in particular which happens rarley but would like some info to confirm.
were can I get another one?? ie: is there a replacment part still available?
dosnt sound like the kind of thing a wrecker would part with unless I bought the whole engine.
Cheers
Powerplant: Chipped stock ECU, 2044cc, 8.5:1, head intake enlarged and polished, exhaust manifold enlarged,
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
- Starion_Turbo
- Enthusiast king
- Posts: 898
- Joined: Wed Dec 08, 2004 5:32 pm
- Location: South Australia
- Contact:
- Starion_Turbo
- Enthusiast king
- Posts: 898
- Joined: Wed Dec 08, 2004 5:32 pm
- Location: South Australia
- Contact:
not a problem I have a timing light so were in business :)
thanx for the info will check it out in next few days
Cheers
thanx for the info will check it out in next few days
Cheers
Powerplant: Chipped stock ECU, 2044cc, 8.5:1, head intake enlarged and polished, exhaust manifold enlarged,
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
Who is online
Users browsing this forum: No registered users and 23 guests