Turboing a 4G54
Turboing a 4G54
A friend's UTE has a carbie 4G54, have been thinking putting a JA TB, inlet manifold, exhaust, ECU + harness, is it doeable?, what's the compression ratio, and are the parts a bolt on affair???
Kiss my st AZZ -
Starions rule the sports car world
GTI-R's are best in the wet..
Who needs Rock & Roll when there's JAZZ, Honda RULEZ
Starions rule the sports car world
GTI-R's are best in the wet..
Who needs Rock & Roll when there's JAZZ, Honda RULEZ
a 4G54 or a 4G64?
If it is a 4G64, then it is doable and the parts will bolt on. What ute is it?
If it is a 4G64, then it is doable and the parts will bolt on. What ute is it?
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
- sigmaproject
- Big Dorifto
- Posts: 91
- Joined: Fri Jan 16, 2004 10:34 am
- Location: Maitland
For a 4g54 you need Magna injection ,not Starion
http://users.chariot.net.au/~emengee/mi ... iprojects/
http://users.chariot.net.au/~emengee/mi ... iprojects/
a few on starquestclub.com have done exactly that.
Look on http://www.starquestclub.com/cgi-bin/st ... rd=mpimods
or
http://www.starquestclub.com/?board=enginemods
for posts by "matbirch", "tainters" or "lizzord"
"shelby" posted lots of details of his turbo truck also
I they all, and "turboraider" started with tbi/stock ecu
some have boosted their non-turbo ~8.5:1 2.6 fine, with good performance
Look on http://www.starquestclub.com/cgi-bin/st ... rd=mpimods
or
http://www.starquestclub.com/?board=enginemods
for posts by "matbirch", "tainters" or "lizzord"
"shelby" posted lots of details of his turbo truck also
I they all, and "turboraider" started with tbi/stock ecu
some have boosted their non-turbo ~8.5:1 2.6 fine, with good performance
this is what im doing....yes its true i dont have a starion :o but a triton 2.6 witch im building up .. this is one of the best sites to find info on the 4g54
________
Lincoln Mark Lt
________
Lincoln Mark Lt
Last edited by nomis on Wed Feb 16, 2011 11:41 am, edited 1 time in total.
-
- Enthusiast
- Posts: 737
- Joined: Wed Feb 02, 2005 2:46 pm
- Location: oregon, USA
- Contact:
The rule of thumb over her ein the states is dont run more than 8lbs on a stock d50 g54b block if you are looking for reliability.
Most people here just use all the g54b starion stuff, since its very straight forward
Most starion guys going mpi use the magna intake with a standalone ecu.
Most people here just use all the g54b starion stuff, since its very straight forward
Most starion guys going mpi use the magna intake with a standalone ecu.
'78 Colt cp, 80 challenger "scorpion" 5spd g54bt conversion almost complete, '80 plymtouh arrow "might max" , '90 mitsu terror van "spacewagon"
80's Hero
80's Hero
how far are you into the conversion??nomis wrote:this is what im doing....yes its true i dont have a starion :o but a triton 2.6 witch im building up .. this is one of the best sites to find info on the 4g54
Kiss my st AZZ -
Starions rule the sports car world
GTI-R's are best in the wet..
Who needs Rock & Roll when there's JAZZ, Honda RULEZ
Starions rule the sports car world
GTI-R's are best in the wet..
Who needs Rock & Roll when there's JAZZ, Honda RULEZ
too eazy
hey Nomis you are everywhere,
you know my tri-26t (triton 2.6 turbo) from the 4g sites,cardomain,downundertruckin, its still carbie but I have
a 4g54 manifold with starion tbi on it (TRUE) and It was a 2.6
in a starion and worked fine
2.6/auto/turbo-garret/starion ecu, all in bed together.
see ya :Phil.
you know my tri-26t (triton 2.6 turbo) from the 4g sites,cardomain,downundertruckin, its still carbie but I have
a 4g54 manifold with starion tbi on it (TRUE) and It was a 2.6
in a starion and worked fine
2.6/auto/turbo-garret/starion ecu, all in bed together.
see ya :Phil.
TORQUES-CHEAP.
sup man yes i am everywhere (a few months ago i got sick spent 5 months in bed so i had a lot of spare time lol) but all good now im still in the middle of the whole thing... iv got a band new magan4G54 block and pistons and im getting better rods and i also have a efi TP full motor witch i will be swapping parts over and i have a 2.6 sigma motor also so im in the middle of mixing all three (but also am in the middle of huge body work so i do a bit here and there)
________
COLORADO MEDICAL MARIJUANA
________
COLORADO MEDICAL MARIJUANA
Who is online
Users browsing this forum: No registered users and 3 guests