All technical questions and answers regarding starions, being modifications to maintenance.
Junkers
Formerly StazzyBabyYeah
Posts: 2338 Joined: Mon Nov 08, 2004 3:16 pm
Location: Christchurch
Post
by Junkers » Thu Jan 27, 2005 7:09 pm
Hi people, i was told by somone that the tbi injectors in a starion would fit into a sonata injection setup, anyone know a little more on this?
I had a glance and they looked like they fit the bill but has anyone had any experience?
Watch your speed - It's virtually impossible to pick it out of the carpet if it gets blown off the table.
Powerslave
Mine is bigger than yours
Posts: 282 Joined: Sun Jan 18, 2004 1:12 am
Location: Brisbane , Queensland
Post
by Powerslave » Thu Jan 27, 2005 7:39 pm
No way.
NXTIME
Registry Nazi
Posts: 2972 Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW
Post
by NXTIME » Thu Jan 27, 2005 7:48 pm
Even JB/JD ones? ;)
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
SpidersWeb
postwhore!
Posts: 1984 Joined: Wed Jan 28, 2004 2:29 am
Location: Wellington, NZ
Post
by SpidersWeb » Thu Jan 27, 2005 10:30 pm
If you did get them to fit. Their spray pattern is likely to be less than ideal as well.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
NXTIME
Registry Nazi
Posts: 2972 Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW
Post
by NXTIME » Thu Jan 27, 2005 10:42 pm
550cc's are plenty.
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
flappa
Lancer is the answer
Posts: 446 Joined: Wed Sep 10, 2003 1:01 am
Location: Australia
Post
by flappa » Thu Jan 27, 2005 11:01 pm
unless you max em out
NXTIME
Registry Nazi
Posts: 2972 Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW
Post
by NXTIME » Thu Jan 27, 2005 11:44 pm
That goes without saying ;) But for most Starions, they are more than sufficient.
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
chunkhead
Mmmmm, I love rice
Posts: 1198 Joined: Thu Sep 30, 2004 2:57 pm
Location: Melbourne
Post
by chunkhead » Fri Jan 28, 2005 10:07 am
I was able to get 13B RX-7 injectors at $90 each! These are going to kick arse!
4G64B
Lil' Dorifto
Posts: 41 Joined: Thu Jan 13, 2005 3:15 pm
Location: Lake Maquarie
Post
by 4G64B » Fri Jan 28, 2005 2:17 pm
Mate I've got 350Hp(atw) in a 2.4 litre(4g64) using the Series IVTurbo RX7 injectors 450Hp fuel pump and run fine max duty cycle about 68% so no way in the world would you need the 850cc ones. WAY TOO BIG
Junkers
Formerly StazzyBabyYeah
Posts: 2338 Joined: Mon Nov 08, 2004 3:16 pm
Location: Christchurch
Post
by Junkers » Fri Jan 28, 2005 8:00 pm
for a low impendance injector such as the vr4 450's or the rx7 550's what is there optimal duty cycle before overheating etc
Watch your speed - It's virtually impossible to pick it out of the carpet if it gets blown off the table.
SpidersWeb
postwhore!
Posts: 1984 Joined: Wed Jan 28, 2004 2:29 am
Location: Wellington, NZ
Post
by SpidersWeb » Fri Jan 28, 2005 8:06 pm
I think the idea is to stay under 80%.
1997 Mitsubishi Lancer Evolution IV 4G63BT
1996 Nissan Maxima VQ30DE (for sale, suit someone who likes the feel of boats when driving)
4G64B
Lil' Dorifto
Posts: 41 Joined: Thu Jan 13, 2005 3:15 pm
Location: Lake Maquarie
Post
by 4G64B » Sat Jan 29, 2005 8:58 am
Sure is .
80% to 90% to give some margin for safety
CussCuss
6pack esky
Posts: 1294 Joined: Fri Jan 09, 2004 1:34 pm
Location: Sydney
Post
by CussCuss » Sun Jan 30, 2005 4:28 pm
the very very very general rule is to divide the cc by 5 and that wil give you the amount of hp the engine can support per cyl, so a 500cc injector will do approximately 400hp at the crank
NXTIME
Registry Nazi
Posts: 2972 Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW
Post
by NXTIME » Sun Jan 30, 2005 5:28 pm
CussCuss wrote: the very very very general rule is to divide the cc by 5 and that wil give you the amount of hp the engine can support per cyl, so a 500cc injector will do approximately 400hp at the crank
...on a 4 cylinder engine, 600hp for a 6 cylinder, etc etc.
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
Junkers
Formerly StazzyBabyYeah
Posts: 2338 Joined: Mon Nov 08, 2004 3:16 pm
Location: Christchurch
Post
by Junkers » Sun Jan 30, 2005 5:38 pm
chunkhead wrote: I was able to get 13B RX-7 injectors at $90 each! These are going to kick arse!
Will they just slot in? i want some!
Watch your speed - It's virtually impossible to pick it out of the carpet if it gets blown off the table.
Users browsing this forum: No registered users and 15 guests