Upgrades to Widebody
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
Upgrades to Widebody
Ok. I have run my car at Willowbank and am running 14.7 seconds down the quarter. I am going to upgrade my car. Firstly, I will list what I want done. I would like you guys to help me out a little. Firstly by telling me what you think I will be pulling. Suggestions on better upgrades and even better prices around. Thanks.
UPGRADES:
1) TD05 19C turbo $1500
2) Microtech EMS MT8 $600 + fitting and tuning
3) Heavy Duty Clutch
4) Pod air filter $100
5) Exhaust (New dump pipe and mandrel bends) Already have good Muffler.
6) Multipoint Injection system
7) Hardened internals
8) King springs $350 then fitting
9) Bigger Intercooler (maybe)
10) Cam
11) Methanol spray $40
UPGRADES:
1) TD05 19C turbo $1500
2) Microtech EMS MT8 $600 + fitting and tuning
3) Heavy Duty Clutch
4) Pod air filter $100
5) Exhaust (New dump pipe and mandrel bends) Already have good Muffler.
6) Multipoint Injection system
7) Hardened internals
8) King springs $350 then fitting
9) Bigger Intercooler (maybe)
10) Cam
11) Methanol spray $40
Stay with the true and tried TD06H-20G, will cost about $1500 tops aswell. Though I have seen Garrett BB T04e 60-1 s' for about $1700 aswell.......but then you need an external wastegate etc
Get one of those cheap Hybrid copy intercoolers, $450 I think tops, 600x300x75 or try and get a 400mm one instead depending on space, bar and plate ofcourse.
MPI with MT8 definately.
Yuo missed out, Equal length exhaust manifold. Stock manifolds start chokin at 150kw atw.
Exhaust and clutch yes.
Cam and head porting should be the last thing you would do, I think.
Get one of those cheap Hybrid copy intercoolers, $450 I think tops, 600x300x75 or try and get a 400mm one instead depending on space, bar and plate ofcourse.
MPI with MT8 definately.
Yuo missed out, Equal length exhaust manifold. Stock manifolds start chokin at 150kw atw.
Exhaust and clutch yes.
Cam and head porting should be the last thing you would do, I think.
I'd be steering more towards a sigma turbo exhaust manifold, TO4 flanged turbo, external gate.
You will probably want to put a magna head on (assuming that yours has jet valves), larger injectors, new intercooler piping.
I assume the microtech is ignition control?
What do you mean by 'hardened internals'?
You will probably want to put a magna head on (assuming that yours has jet valves), larger injectors, new intercooler piping.
I assume the microtech is ignition control?
What do you mean by 'hardened internals'?
4G63 - 87kg
4G54 - 107kg
4G54 - 107kg
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
upgrades
First of all, My engine is the 2.6Ltr engine. As far as I know it is basically the Magna head. Also, The first thing I am doing is the turbo so would the sigma turbo manifold bolt straight on? If so, Gimme gimme. Because I do want to go towards the T04 more then the TD05 19C or TD06 20G.
I mean by hardened internals Getting my engine worked with forged pistons, conrods ect to make it stronger. Not really stroking it though. Just a bore Polish and port. I will get the exhaust and EMS system but I'm not sure if I will be popping clutches with the extra power coming out of it.
I mean by hardened internals Getting my engine worked with forged pistons, conrods ect to make it stronger. Not really stroking it though. Just a bore Polish and port. I will get the exhaust and EMS system but I'm not sure if I will be popping clutches with the extra power coming out of it.
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
manifold
Anyone know where I can get a sigma exhaust manifold from? or If anyone has one?
I have one and yes it will bolt onto the head. Whether it clears other things in the engine bay is another matter. Expect to pay $400ish when/if you find one. Keep your eyes on ebay.
The US 2.6 ran the jet valve head and I suspect the japs also ran it. These are a big problem especially when boosting HP hence why I said that you may need to upgrade to the magna head.
You may want to upgrade to forged pistons, but the stock rods and crank are fine, just allow $$ for a good balance after deleting the balance shafts.
The US 2.6 ran the jet valve head and I suspect the japs also ran it. These are a big problem especially when boosting HP hence why I said that you may need to upgrade to the magna head.
You may want to upgrade to forged pistons, but the stock rods and crank are fine, just allow $$ for a good balance after deleting the balance shafts.
4G63 - 87kg
4G54 - 107kg
4G54 - 107kg
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
head
I found a manifold for $450 USD that I can get anytime but It might be too much. Also, I am going to get the foged pistons and the rest because I can get it done cheap through my mechanic on the coast. he works on my car all the time for next to nothing. So I am basically paying for hardware and no labour.
I will keep a look out and do you get a heap of power from eliminating the balance shafts? I always hear about them but never thought about it.
I will keep a look out and do you get a heap of power from eliminating the balance shafts? I always hear about them but never thought about it.
Re: upgrades
That's what's in my widebody as well. Except mine has a Magna head and cam. Ralliart TD06/19C and exhaust manifold going on soon stay tuned :DWidebodyWoody wrote:First of all, My engine is the 2.6Ltr engine.
- Cookiemonster
- Mother Goose
- Posts: 3177
- Joined: Thu Jan 08, 2004 4:33 pm
- Location: Sydney
secondedNXTIME wrote:you're all bastards....
....and I mean that in the nicest sense :D:D:D
_
_________________
_________________
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
LOL
Then get off your asses and do something about it. I owned a JA for a year before I invested in a widebody. It is the best thing I have ever done in my life. I will post a heap of pics on the site after the brisbane autosalon. They should be some good pics and hopefully some magazine offers. I will be in QLD street car mag soon.
Who is online
Users browsing this forum: No registered users and 13 guests