Spray Adhesive?

Camotec · Post by **Camotec** » Mon Mar 29, 2004 1:19 am

Anyone know where i might find some really good spray adhesive?

Cheers :)

toysrus · Post by **toysrus** » Mon Mar 29, 2004 9:18 am

hardware stores :D Ask for a contact adhesive spray :D

Camotec · Post by **Camotec** » Mon Mar 29, 2004 10:40 am

key words "really good" heh, I have been through mitre 10 and material stores like spotlight for a good adhesive and most of them will not stand up to time as I already have bits peeling and this is only after a week of adhesion.

And you can't use too much spray as it goes through the fabric and makes it hard too, wrecking the finish of the micro suede.

Anyways i will check out a few more places, might try bunnings, see if they have anything strong.

Cheers.

Will · Post by **Will** » Mon Mar 29, 2004 12:19 pm

I gather this is for a car interior? I used a brush on contact adhesive which I got from this place:

Car Console Supplies Pty Ltd
409 Princes Hwy Carlton NSW 2218
ph: (02) 9546 7914 Motor Body Trimmers

They sold them in tomato paste jars as they bought in bulk. Lasted for over a year and then I sold the vehicle, so its still probably still going strong. Used it for glueing cloth/velour trim.

Camotec · Post by **Camotec** » Mon Mar 29, 2004 12:21 pm

Thanks will will give them a call :)

Cheers

Cam · Post by **Cam** » Mon Mar 29, 2004 12:51 pm

The shit you'll get from them is most likely the same as what is used to stick laminate down. is strong shit, just make sure you get it in the right spot first go or its fucked ;)
Trust me i know

ProZac · Post by **ProZac** » Mon Mar 29, 2004 1:16 pm

Ive had good experiences with "Ados Contact Adhesive", both the brush on the spray on forms.

Will · Post by **Will** » Mon Mar 29, 2004 2:55 pm

The stuff I used was kind of brown'ish orange in colour. It did make the material go hard if you used too much too. I was told that you had to use stuff that could withstand the temperatures in a car without going soft. If you ring up, they might be able to tell you what brand etc. so you can source locally.

toysrus · Post by **toysrus** » Mon Mar 29, 2004 8:03 pm

go to your local mitre 10 and buy some "Kwik Grip" apply it to both surfaces and let it settle for about a minute the join both surfaces together!

Doing it that way and it will never fall apart!!!

Camotec · Post by **Camotec** » Mon Mar 29, 2004 8:20 pm

I have kwik grip and it is a thick paste in a tube not really good for material bonding when you still want the soft material feel.

but kwik grip does hold on :)

robert26t · Post by **robert26t** » Fri Jun 18, 2004 3:45 pm

Ya cant go wrong with the good ol Jaycar stuff.. Just make sure you let it go sticky before you try and stick stuff together otherwisw it wont work :?

http://www1.jaycar.com.au/productView.a ... &SUBCATID=

decoy · Post by **decoy** » Sat Jun 19, 2004 1:15 am

ProZac wrote:Ive had good experiences with "Ados Contact Adhesive", both the brush on the spray on forms.

ProZac · Post by **ProZac** » Sat Jun 19, 2004 1:16 pm

lol, your a bastard Deeks ;)

decoy · Post by **decoy** » Sun Jun 20, 2004 11:10 pm

rofl i only do it cos i love ya rofl

Steve E · Post by **Steve E** » Mon Jun 21, 2004 5:46 pm

You 2 are starting to worry me, rofl :D

Austarion

Spray Adhesive?

Spray Adhesive?

Who is online