Hey John
If they were slow I wouldn't have mind, but after taking payment and saying they could do it as they had the measurements from you. It took them over 3 months to tell me that they would only make them if I could get an order of 10. They did refund me but I lost hundreds from the fx transactions.
My JB Track Car
-
John196701
- I like starions
- Posts: 108
- Joined: Fri Jun 18, 2010 9:36 pm
- Location: Camden
Fantastic work mate!!! :beer
Ill be following this build closely.
What year Hyundai Excel was the steering rack from?
Ill be following this build closely.
What year Hyundai Excel was the steering rack from?
1984 Sigma Super, Turbo Wagon
1990 GSR-VR 50,000ks
1984 GSR II 4G63 302kw atw at 24psi
http://www.facebook.com/marvinmartiannz
1990 GSR-VR 50,000ks
1984 GSR II 4G63 302kw atw at 24psi
http://www.facebook.com/marvinmartiannz
-
John196701
- I like starions
- Posts: 108
- Joined: Fri Jun 18, 2010 9:36 pm
- Location: Camden
Jason
the manual steering racks i think are all the same, they run around 3 turns lock to lock, the main thin i was after was the distance between the 2 inner ball joints was almost the same as the inner rod ends mounted on the drag link, this will minimize the chance of bump steer
John
the manual steering racks i think are all the same, they run around 3 turns lock to lock, the main thin i was after was the distance between the 2 inner ball joints was almost the same as the inner rod ends mounted on the drag link, this will minimize the chance of bump steer
John
JB Starion Black, owned since 1988
JB Starion Black, track car build
Given that I've no experience on a race track, excuse the noobishness, but is the steering box so bad?
The E39 M5 uses a steering box system, and this car has been praised by everyone around the world to no end..
Incidentally, I was looking up m5 steering problems and came accross this (look at post number 9):
http://www.m5board.com/vbulletin/e39-m5 ... oable.html
The E39 M5 uses a steering box system, and this car has been praised by everyone around the world to no end..
Incidentally, I was looking up m5 steering problems and came accross this (look at post number 9):
http://www.m5board.com/vbulletin/e39-m5 ... oable.html
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
-
redzone
- racking my brains
- Posts: 5900
- Joined: Thu Oct 06, 2005 10:46 pm
- Location: sunshine coast qld
- Contact:
240sx = s13 = Silo's setup
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q
www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q
www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
Yeap. Seems like he's not the only one who did it :)
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
-
ProZac
- G33Kz0r
- Posts: 2674
- Joined: Thu Nov 27, 2003 1:26 pm
- Location: Christchurch, New Zealand
- Contact:
Plenty of the US guys have done it, but the rack end pivot points on the S13 racks are a bit wider than the control arm mounting points on the front crossmember. They don't seem to complain, but if you can find a rack with pivot points more inline with the control arm mounting points, you might aswell use it.
Not a problem for the way Silo did it, as he used the entire S13 crossmember, with the Starion framerail and engine mounts welded on, giving correct geometry for the S13 rack, with S13 lower arms.
Not a problem for the way Silo did it, as he used the entire S13 crossmember, with the Starion framerail and engine mounts welded on, giving correct geometry for the S13 rack, with S13 lower arms.
Who is online
Users browsing this forum: No registered users and 38 guests