Line Lock, Shut off valve, or proportioning valve??

All technical questions and answers regarding starions, being modifications to maintenance.
Post Reply
User avatar
JAS
Enthusiast king
Posts: 993
Joined: Sun Mar 14, 2004 8:27 am
Location: Christchurch

Line Lock, Shut off valve, or proportioning valve??

Post by JAS »

I need to fit one of the above as when I did a bit of a burnout the other day (not on the road) the rear brakes were grabbing a bit more than I would have liked. And as Im going to do a bit of drag racing in it in the summer Im going to need to do something.....

I kind of like the idea of fitting a shut off valve to the rear line. That way I still have control of the fronts as normal.

http://www.wilwood.com/MasterCylinders/ ... o=260-9921

Just wondering what other people are using and what is the best way around fitting one of these to a street car as they are ilegal in most places.
1984 Sigma Super, Turbo Wagon
1990 GSR-VR 50,000ks
1984 GSR II 4G63 302kw atw at 24psi

http://www.facebook.com/marvinmartiannz

ImageImage
User avatar
Alspos
Flucking kwankers
Posts: 4107
Joined: Thu Jan 08, 2004 2:09 pm
Location: Melbourne
Contact:

Post by Alspos »

The other way is a line locker. Like this.

Pump up the brakes, hit the switch and they lock on.

I doubt any of this stuff would be legal on a road car.....just don't tell :wink:
ProZac
G33Kz0r
Posts: 2674
Joined: Thu Nov 27, 2003 1:26 pm
Location: Christchurch, New Zealand
Contact:

Post by ProZac »

One of those willwood units installed just before the manifold which splits the rear line out to either side of the car (just infront of the fuel tank) would be pretty cool, and should work pretty well. Must be somewhere under there to hide it nicely?

"Its just a brake fluid pressure sensor Mr WOF Man...." :-).
User avatar
Lunacy
nearly postwhore
Posts: 1355
Joined: Fri Jul 22, 2005 3:31 pm
Location: Land of Confusion

Post by Lunacy »

Reverse swing clutch and brake pedal kit with dual brake masters and dash mounted balance bar adjuster. :twisted:
Image
User avatar
JAS
Enthusiast king
Posts: 993
Joined: Sun Mar 14, 2004 8:27 am
Location: Christchurch

Post by JAS »

ProZac wrote:One of those willwood units installed just before the manifold which splits the rear line out to either side of the car (just infront of the fuel tank) would be pretty cool, and should work pretty well. Must be somewhere under there to hide it nicely?

"Its just a brake fluid pressure sensor Mr WOF Man...." :-).
I was thinking about mounting it close to the master cylinder behind the heat sheild. You would have to look really hard to find it there! :D

Lunacy wrote:Reverse swing clutch and brake pedal kit with dual brake masters and dash mounted balance bar adjuster. :twisted:

Show off :p lol
1984 Sigma Super, Turbo Wagon
1990 GSR-VR 50,000ks
1984 GSR II 4G63 302kw atw at 24psi

http://www.facebook.com/marvinmartiannz

ImageImage
kiwieurospec
Enthusiast
Posts: 605
Joined: Thu Apr 06, 2006 2:21 pm
Location: Christchurch,New Zealand

Post by kiwieurospec »

You don't have enough grunt there JAS. :)

It ain't gonna worry you out at Ruapuna, my stocker could sit there as long as I wanted with 60 series tyres and all. You start burnouts out there on wet concrete and then they don't like you using the brake on the tarmac. (because dual use racetrack)
1985 Widebody Factory Four Wheel Steering
1986 Euro Spec-ABS,LSD etc
User avatar
JAS
Enthusiast king
Posts: 993
Joined: Sun Mar 14, 2004 8:27 am
Location: Christchurch

Post by JAS »

haha. Thats it Daniel!! :) NOS must be next hehe.

Ok, thats interesting. Think Ill still fit a shut off valve though. Just in case the burn out mood arises again and Im not on wet concrete :D
1984 Sigma Super, Turbo Wagon
1990 GSR-VR 50,000ks
1984 GSR II 4G63 302kw atw at 24psi

http://www.facebook.com/marvinmartiannz

ImageImage
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests