WTB :: Aftermarket Ecu, Suit SOHC 4g63

[GormzZ]

As the title says.. im still on the lookout for a aftermarket ecu/loom with basic ign/fuel tuning abilities so i can get my mpfi running on my starion. Don't mind if its second hand or near new.. Just need something for a reasonable price as im sick of uhmming and ahhing about what to get.

Throw me some options please!!

[1320ft]

I have a EMS Dualsport V7 with handset here you can have for a couple of hundred. Just needs to be remapped for the 4G, was on a 13BT rx-7.

[GormzZ]

Can you shoot me a pm mate on specs for it etc.. Interested though!

[GormzZ]

Bump, still on lookout at this point.

[bigmoz]

http://www.ebay.com.au/itm/microtech-lt ... 27d071564f

[Starion VR4]

http://www.ebay.com.au/itm/microtech-lt ... 27d071564f

Thats not a bad unit & good Price... don't really think you will get anything cheaper that is still good quality... I do have a few Wolf units but really don't want to move them on. Do you have the MPI Manifold ? I have two units if you need one. :beer

[GormzZ]

Yeah seen the microtech ecu's there for round a grand.. but got given two options recently.. so will see if they could be goers first before i have to come back again.. but people can keep offering anyway! and yeah mate.. got the mpfi manifold here, custom l300 manifold.. but i need ecu and loom badly before having nearly all the gear to finish the setup.

[EVOMINUS]

http://www.starquestclub.com/forum/inde ... 135968&hl=

this is mine
trust me i have used this ecu for only about 15 hours and i only sell it because i desperatly need the money
I tried putting it on ebay but there are limits when it comes to the price so that never went through
I used a bone stock 6 bolt ,changing only the peripherals 780cc,a tme turbo and a big fmi and the car made almost 400whp and 53 kg of torgue
The car was a BEAST!!!!!!
I am at your disposal for whatever you need and if you sent me your email i will be able to sent you some pics

[ProZac]

Have you thought about trying to use an EVO V or above ECU? they're re-mappable in place without having to open anything using a tuner cable, which would run you approximately $150AUS.

Downside is that you'd be locked into the mitsy 4-2 triggering pattern, so would have to find a way to get that signal from your SOHC motor.

I've just built the loom to run my SOHC MPI setup on an EVO V ecu. I've had it all working on the bench, wasen't any harder than an aftermarket ecu install.

[Starion VR4]

Have you thought about trying to use an EVO V or above ECU? they're re-mappable in place without having to open anything using a tuner cable, which would run you approximately $150AUS.

Downside is that you'd be locked into the mitsy 4-2 triggering pattern, so would have to find a way to get that signal from your SOHC motor.

I've just built the loom to run my SOHC MPI setup on an EVO V ecu. I've had it all working on the bench, wasen't any harder than an aftermarket ecu install.

Thats an option but the expense of a EVO ECU & Harness would put you right on par with aftermarket?

GormezZ I do have a few WOLF ECU's in fact a may remove my WoLF V4 from my Staz if you can't find anything you want. :beer

[GormzZ]

@Evominus.. its a little out've my price range for what it is man..

@ProZac, nahh i actually haven't mate, yeah i'd have to refer to your thread in regards to that. I believe any wiring work will be done by a mate or someone else with knowledge as mine is very basic with that stuff..

@Starion VR4, Yeah man will let you know in this thread or by pm if the others fall through.. one of them sounds like a good deal.. just waiting to find out what sort've money his talking lol.