Head Gasket or not?

All technical questions and answers regarding starions, being modifications to maintenance.
GasJA
I like starions
Posts: 111
Joined: Tue Oct 31, 2006 10:39 pm
Location: Geelong

Head Gasket or not?

Post by GasJA »

I think I have done a head gasket.
Last month or so the brake light was coming on and I noticed a split in the vacuum line at the manifold end. Cut one cm off the rubber tube at the manifold end. Sometimes the brake light would not come on.
Idling has been erratic last month.

Last night the sound of the engine changed and I thought I must have a hole in my relatively new exhaust.
This morning the car was really difficult to start. I checked my oil and it was at min. Coolant was low and added 2 litres to top up the radiator. Has been a while since I checked both.
When I got the car started and running for 2 minutes I noticed some bubbles in the top of the oil on the dipstick. Coolant level had not changed much.

If it is a head gasket what is a good option for a stronger head gasket and a supplier in Melbourne/Geelong. Funds are limited at the moment - what would the cost be approx.
Also is it advisable to install new/different head bolts.
4G63 hard to live with
hard to live without..
GasJA
I like starions
Posts: 111
Joined: Tue Oct 31, 2006 10:39 pm
Location: Geelong

Post by GasJA »

Just had another look after the engine cooled down.
Looks like the exhaust manifold (I replaced the gasket last month) was held on by three nuts only. Dodgy workmanship on my part.
I used Champion pack Brass Manifold Nuts M8 x 1.25 (Nissan) with Champion 316 8mm SS washers. Do I need to use spring washers or?

Also the "acordian" air intake hose was split at the turbo end. I remember someone posted a fix for this on the forum.
4G63 hard to live with
hard to live without..
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

I'd be using spring washers on the manifold, then you are less likely to lose any.

As for the intake hose, I'd get that fixed.

Sounds like you'll need to keep an eye on the coolant levels, check all your hoses are tight and in good condition, including the heater hoses.

If you can get a compression gauge, preferably a screw in type, that might give you some more idea too.
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
GasJA
I like starions
Posts: 111
Joined: Tue Oct 31, 2006 10:39 pm
Location: Geelong

Post by GasJA »

Thanks for that. Ages ago I did the engine swap myself and probably forgot to put spring washers on.
I sent a PM to alspos to try and get the pix for the turbo intake hose repair.
4G63 hard to live with
hard to live without..
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

You need lock nuts not spring washers, spring steel loses it's effect when heated. Toyota ones are good (genuine part)
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
GasJA
I like starions
Posts: 111
Joined: Tue Oct 31, 2006 10:39 pm
Location: Geelong

Post by GasJA »

Thanks for that will give the Toyota ones the go.
4G63 hard to live with
hard to live without..
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

redzone wrote:You need lock nuts not spring washers, spring steel loses it's effect when heated. Toyota ones are good (genuine part)
Ah! That explains why they're not usually that tight...
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
User avatar
Lunacy
nearly postwhore
Posts: 1355
Joined: Fri Jul 22, 2005 3:31 pm
Location: Land of Confusion

Post by Lunacy »

I find the best thing to keep those studs tight is nordlock washers! Never had an issue with them coming loose, even after repeated heat cycles.
http://www.nord-lock.com/default.asp?url=2.16.37
Image
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

another option which i use are the wurth copper coated locknuts
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

redzone wrote:another option which i use are the wurth copper coated locknuts
Given that they are wurth brand, you'd have to hand over a kidney or your left nut or something for payment? Are they really wurth it? :wink: :wink:
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
User avatar
Alspos
Flucking kwankers
Posts: 4107
Joined: Thu Jan 08, 2004 2:09 pm
Location: Melbourne
Contact:

Post by Alspos »

I might have to contact a mate of mine who works at Wurth for some "samples" then hehehe
dirtygalant
nearly postwhore
Posts: 1446
Joined: Sun Jun 19, 2005 7:27 pm
Location: Sunny Brisbane Australia!

Post by dirtygalant »

brake light might be low on brake fluid in the reservoir or faulty handbrake switch.
ImageImage
E39A Galant VR-4 Evolution | A164A Eterna GSR | 6G72 RWD Conversion Forum
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

I can confirm that they're 100% wurth it!
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

dirtygalant wrote:brake light might be low on brake fluid in the reservoir or faulty handbrake switch.
One of the first things I do with a Starion is disconnect the plug for the handbrake lamp. I don't need a bloody light to tell me the handbrake is on every time I yank the thing on...and ask anyone that knows me, I use the handbrake a lot!
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
GasJA
I like starions
Posts: 111
Joined: Tue Oct 31, 2006 10:39 pm
Location: Geelong

Post by GasJA »

Update. Compression test on engine 60000km straight gas never run on petrol since rebuild.
Burnt ring finger on turbo.
Bit hard to read my Stanley compression tester.
Cylinders 1 to 4. 160, 157, 165, 160psi. or 1100, 1060, 1140, 1100KPa.
Exhaust system OK. Getting a gas service with Rapidflow next week.
4G63 hard to live with
hard to live without..
Post Reply

Who is online

Users browsing this forum: No registered users and 10 guests