Wideblock 4g64 TC build with lots of pics from JapNostalgic

For all your twin cam conversion questions and hints
Post Reply
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Wideblock 4g64 TC build with lots of pics from JapNostalgic

Post by enthuzed »

Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

Worth mentioning that this build has the thermostat and CAS relocated to the front of the motor.
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
User avatar
thrash
Austarion Occupant
Posts: 3028
Joined: Mon Apr 02, 2007 10:09 pm
Location: Sydney, Australia

Post by thrash »

:D

nice work that one!

I'm hoping that when I have about 7 or 8 grand spare, my engine blows a head gasket or something, so I have an excuse to build a 2.4 and feed extreme amounts of boost through it..

is that one of the cas from an rvr? I wonder if there is a way to replicate it.. or I wonder a crank angle sensor from a late mode 4g63 could be adapted...
quest wrote:
WANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
don't try explaining that to her tho..... just leave. lol
dwlee
[P] Plates
Posts: 34
Joined: Tue Sep 26, 2006 10:15 am
Location: Auckland NZ

Post by dwlee »

If you read the thread you will find that he tried to use a 7bolt oil pump housing with the crank angle sensor on a 6bolt block and ran into issues, so replaced the 7bolt oil pump housing with a 6bolt housing and replaced the factory crank angle sensor with a Kiggly Racing Crank trigger. The cam angle sensor is most likely from a 95/96 gen2 Eclipse and are the same as the rvr. I have seen quite a lot of 7bolt heads that have the bosses that the sensor bolts even when they are factory fitted with a rear cas, so it shouldn't be to hard to fit.
fugazi
Enthusiast
Posts: 716
Joined: Thu Oct 02, 2008 10:30 pm
Location: Stockholm, Sweden
Contact:

Post by fugazi »

One of the first things I personaly would have done was moving the PS-pump to the LHS on a LHD-car... giving a lot more space for the turbo and stuff... and lesser PS-lines.
But still, nice work done there!
Image
OLD FART
Austarion Occupant
Posts: 3448
Joined: Sun Jun 19, 2005 1:34 pm
Location: Brisbane

Post by OLD FART »

fugazi wrote:One of the first things I personaly would have done was moving the PS-pump to the LHS on a LHD-car... giving a lot more space for the turbo and stuff... and lesser PS-lines.
But still, nice work done there!
My PS pump is down low under the TB so the turbo can be positioned forward of the factory position for easier dump bends and less restrictive IC pipework.
I've had mine since 03 07 92
85 JB 2323cc DOHC 4G63
THE OLDER I GET THE FASTER I WAS
GROWING OLD IS MANDATORY GROWING UP IS OPTIONAL
fugazi
Enthusiast
Posts: 716
Joined: Thu Oct 02, 2008 10:30 pm
Location: Stockholm, Sweden
Contact:

Post by fugazi »

Exacley what I meant O.F!
My intentions in the next build...
Image
rodney007
I love starions
Posts: 381
Joined: Mon Dec 10, 2007 6:01 pm
Location: NEW ZEALAND

Post by rodney007 »

OLD FART wrote:
fugazi wrote:One of the first things I personaly would have done was moving the PS-pump to the LHS on a LHD-car... giving a lot more space for the turbo and stuff... and lesser PS-lines.
But still, nice work done there!
My PS pump is down low under the TB so the turbo can be positioned forward of the factory position for easier dump bends and less restrictive IC pipework.
Yep works well, Got an idler setup running from front engine mount down that way, stoped it kicking the damn belt.

Was going to use starion PS pump but would have had to be upside down or to far out to side to fit lines so I used a 2001 Lancer FWD unit.
User avatar
thrash
Austarion Occupant
Posts: 3028
Joined: Mon Apr 02, 2007 10:09 pm
Location: Sydney, Australia

Post by thrash »

did you guys custom make the brackets or were they off another car?
quest wrote:
WANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
don't try explaining that to her tho..... just leave. lol
OLD FART
Austarion Occupant
Posts: 3448
Joined: Sun Jun 19, 2005 1:34 pm
Location: Brisbane

Post by OLD FART »

thrash wrote:did you guys custom make the brackets or were they off another car?
Used the aircon bracket
I've had mine since 03 07 92
85 JB 2323cc DOHC 4G63
THE OLDER I GET THE FASTER I WAS
GROWING OLD IS MANDATORY GROWING UP IS OPTIONAL
rodney007
I love starions
Posts: 381
Joined: Mon Dec 10, 2007 6:01 pm
Location: NEW ZEALAND

Post by rodney007 »

OLD FART wrote:
thrash wrote:did you guys custom make the brackets or were they off another car?
Used the aircon bracket
same here
Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests