Gormzz's Stazza..!

GormzZ · Post by **GormzZ** » Wed Feb 15, 2012 5:57 pm

yeah i will do it if i can get a image diagram of the wiring setup.. as i have no idea where to start with the numbers enthuzed has mentioned above...

Post by **TOMSUN** » Wed Feb 15, 2012 7:34 pm

GormzZ wrote:yeah i will do it if i can get a image diagram of the wiring setup.. as i have no idea where to start with the numbers enthuzed has mentioned above...

Here is a thread from ages ago with some details.
http://forums.austarion.com/viewtopic.p ... otor+relay

Wiring diagrams can be had from the "TECHNICAL" link at the top of the website.

enthuzed · Post by **enthuzed** » Wed Feb 15, 2012 7:37 pm

Here ya go:

Post by **TOMSUN** » Wed Feb 15, 2012 7:37 pm

scratch that... I just read enthuzed's post again and it looks almost identical to mine from 2006... :D

enthuzed · Post by **enthuzed** » Wed Feb 15, 2012 7:44 pm

You'll need this:

Get some terminals to suit the plug, and some eyelet terminals, one big enough for the starter solenoid that gets screwed on with a nut and a smaller one for the earth.

Use decent gauge wire and then a suggestion for you, mount it next to the compliance plate on the firewall, which is high above the starter/clutch slave cable.

GormzZ · Post by **GormzZ** » Wed Feb 15, 2012 8:30 pm

much better!! appreciated heaps guys. will be doing that and ripping the starter motor out asap to see what the go is.. and hopefully getting a new starter if need be within the next few days/week.. then of to get a roady and she will be on road so i can do the rest of my mods!

GormzZ · Post by **GormzZ** » Sun Feb 19, 2012 8:15 pm

to set up my front mount will i need to just buy a generic ebay intercooler kit or is their a premade one?

OLD FART · Post by **OLD FART** » Mon Feb 20, 2012 5:04 am

GormzZ wrote:to set up my front mount will i need to just buy a generic ebay intercooler kit or is their a premade one?

The cooler will have to be custom made or ebay as there are no kits available TMK :( Tripple 9 at Coopers plains and Autobarn have a range of the China IC's in Brisbane.
If you search there are pics as to where to mount them.

GormzZ · Post by **GormzZ** » Mon Feb 20, 2012 6:20 pm

i've got a fullsize intercooler here.. just need to find out what piping to suit.. regarding bends and so forth.

redzone · Post by **redzone** » Mon Feb 20, 2012 8:04 pm

are u gonna run the a/c still?

GormzZ · Post by **GormzZ** » Mon Feb 20, 2012 9:52 pm

not sure at this point.. would consider removement of it.. but everything in the car functions.. which for its age is a plus! whys that?

redzone · Post by **redzone** » Mon Feb 20, 2012 10:22 pm

it will influence where u put the cooler. a 600X300X76 is just a little too large to fit comfortably, search on here for intercooler fitment, hopefully there are some pics left..

Post by **TOMSUN** » Mon Feb 20, 2012 10:28 pm

Yup a 450x300 core with 2.5" inlet/outlets is the pick...

fugazi · Post by **fugazi** » Mon Feb 20, 2012 11:19 pm

Naaah!
No problem fitting a bigger one:
http://forums.austarion.com/viewtopic.php?t=13173

GormzZ · Post by **GormzZ** » Tue Feb 21, 2012 6:30 pm

yeah link above with what fugazi had done was my plan to fit it. so much room behind that front bar so why not.

Austarion

Gormzz's Stazza..!

Who is online