1320ft's 2.3L Strip Warrior, Cage is in PG8

Display your ride and post power figures, dyno runs, drag and circuit times.
Post Reply
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

I actually picked up the box second hand from a reliable seller.

But Norm at Northmead Auto's will check it over and after we have dyno'ed the car, the converter will come out and be given to Slingshot to be checked.

The box allready has the 6 cyl input shaft and clutch packs installed. Plus has been manualised and reverse pattern.
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

Tossing up between these two atm, because I may just go straight to the Live rearend to save mucking around.

Image

Image
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
User avatar
jk
Mine is bigger than yours
Posts: 317
Joined: Sat Apr 18, 2009 10:22 pm
Location: SOR Perth WA

Post by jk »

save weight and go the blue kit.
jb - white outside maroon inside
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

nice one 1320 thats an awesome find second hand!
any idea what stall level you'll put in?
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

Not yet.

Stall speed is something that will depend on final diff ratio, cam profile etc.
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

This is the diff that will be going in.

Image

It is only a Borg Warner, but its got some goodies inside it that has allowed it to run deep into the 8 sec zone.
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

nothing wrong with that diff mate!
just heaps wrong with the cars they came out in!
having said that now that their potential is being tapped there are vl's in the 8's still running them :beer
how much you gonna shorten it?
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

Bar work has been picked up and is ready to notch and weld in.

I couldnt believe how quick they turned it around. Had the call back within 24hrs saying it was ready to pick up.

Its a behind the dash kit, 6 point in Mild Steel.

Image
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

So I am at somewhat of a crossroads today.

After spending the last two days out at Superlap I am somewhat tempted to put a good IRS setup back in the car, get a manual and set the car up to do both drags and circuit racing. Obviously via auto back in when I go drag racing and manual for circuit.
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
User avatar
Sargeant_Khan
Enthusiast
Posts: 673
Joined: Thu Dec 16, 2004 9:31 pm
Location: Ipswich

Post by Sargeant_Khan »

Aaron, while the cage piping is out of the car, would you mind weighing it all for me?
Cheers
Jay
Image
PIZZA DELIVERY GUY....No more
TOMSUN
Group buy King
Posts: 2391
Joined: Fri Sep 10, 2004 10:24 am
Location: Sydney (Liverpool)

Post by TOMSUN »

1320ft wrote:So I am at somewhat of a crossroads today.

After spending the last two days out at Superlap I am somewhat tempted to put a good IRS setup back in the car, get a manual and set the car up to do both drags and circuit racing. Obviously via auto back in when I go drag racing and manual for circuit.
Stay the course... Keep it as a drag car. :D
1985 JB Starion #157
User avatar
NXTIME
Registry Nazi
Posts: 2972
Joined: Thu Jan 08, 2004 3:14 pm
Location: Sydney, NSW

Post by NXTIME »

Yep, drag car...it's in your blood ;)
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>


1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
User avatar
thrash
Austarion Occupant
Posts: 3028
Joined: Mon Apr 02, 2007 10:09 pm
Location: Sydney, Australia

Post by thrash »

sorry to pull a cliche on you, but i think that you will find that if you make it a jack of all trades, it will not master either.

having said that, time attack does look like awesome fun, doesn't it??
quest wrote:
WANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
don't try explaining that to her tho..... just leave. lol
User avatar
Sargeant_Khan
Enthusiast
Posts: 673
Joined: Thu Dec 16, 2004 9:31 pm
Location: Ipswich

Post by Sargeant_Khan »

Thrash is right, though its alot of money to spend on a car thats fun factor only lasts for ten seconds.
Image
PIZZA DELIVERY GUY....No more
User avatar
1320ft
almost postwhore
Posts: 1071
Joined: Mon May 03, 2010 8:33 pm
Location: St Andrews NSW

Post by 1320ft »

Sargeant_Khan wrote:Aaron, while the cage piping is out of the car, would you mind weighing it all for me?
Cheers
Jay
No worries mate.

Yes, I am still a drag racer at heart, I would like to be able to enjoy the car a little more than the occasional wed night, TnT & Jambo etc.

While I ponder over this, I have asked a CAMS scrutineer customer of mine, what extra bars would be required to be added to my cage, to run superlap.
The Forum Parts Guy

www.vibrantperformance.com for all your performance fabrication needs

IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car

Here to run out of your life & take all your money!
Post Reply

Who is online

Users browsing this forum: No registered users and 58 guests