will these wheels fit?

All technical questions and answers regarding starions, being modifications to maintenance.
Post Reply
User avatar
bigmoz
Enthusiast king
Posts: 886
Joined: Thu Jan 22, 2004 1:04 pm
Location: Melbourne Australia

will these wheels fit?

Post by bigmoz »

i dont mind if i have to roll the guards a bit on the front im just concerned about how close the tire will be to te strut im pretty sure the back will fit without changing anything

http://www.ebay.com.au/itm/Rota-GRIDR-1 ... 1e624446ed

moz[/u]
85 JB, forged, larger valves, ported and polished microtech, sonata mpi, td06 20g, intercooler, willwood brakes, koni suspention, 3.9LSD and more shit i cant remember

82 JA, blueprint SIRUS 4g63, dumped and a cooler 17's, exhaust... DEAD :(
big moz (chopyou@hotmail.com)
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

rear will be fine
9" on the front is pushing it.

pretty sure these details have been covered off about 100 times in this section
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
User avatar
thrash
Austarion Occupant
Posts: 3028
Joined: Mon Apr 02, 2007 10:09 pm
Location: Sydney, Australia

Post by thrash »

+12 with no dish.. hmmm
quest wrote:
WANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
don't try explaining that to her tho..... just leave. lol
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

^^^ good call.

big money difference between these and 3 piece or billet though ay.
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
User avatar
perrinsohc
Mine is bigger than yours
Posts: 315
Joined: Sat Mar 20, 2010 4:53 pm
Location: Sydney/Christchurch

Post by perrinsohc »

10's on the front on a wide body will be sweeeeet as lol
Image


87 Starion EX
Top
User avatar
bigmoz
Enthusiast king
Posts: 886
Joined: Thu Jan 22, 2004 1:04 pm
Location: Melbourne Australia

Post by bigmoz »

i only want 9 on the front im putting 9.5 on the rear i just want to know will the off-set be right so it doesnt rub on the struts??? guards can always be rolled

moz
85 JB, forged, larger valves, ported and polished microtech, sonata mpi, td06 20g, intercooler, willwood brakes, koni suspention, 3.9LSD and more shit i cant remember

82 JA, blueprint SIRUS 4g63, dumped and a cooler 17's, exhaust... DEAD :(
big moz (chopyou@hotmail.com)
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

Mick wrote:rear will be fine
9" on the front is pushing it.

pretty sure these details have been covered off about 100 times in this section
yeah mate, youre all good
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:
Contact redzone

Post by redzone »

Yeah for the millionth time, 9's on the front will require a ZERO offset, otherwise they'll hit the strut. You will also require neg camber so it doesnt hit the guard lip.
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
Top
Post Reply

Return to “Technical”

Who is online

Users browsing this forum: No registered users and 17 guests