Clean... Still no polish

Display your ride and post power figures, dyno runs, drag and circuit times.
Post Reply
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

possibly down the track... with the cost of changing over it'd be nearly the same to get showwheels to custom make another set of wheels i reckon :wink:
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
Komeuppance
Enthusiast
Posts: 607
Joined: Fri Nov 16, 2007 3:50 pm
Location: Oregon, USA
Contact:
Contact Komeuppance

Post by Komeuppance »

Mick wrote:Robert how is it that you enjoy any narrow body given that you live among wideys? :beer
I have both, and with the right touches they both can look equally good. I'm addicted to Starions, and Starion accessories... lol.

-Robert
Image
Now: Australian Compatible!
Top
User avatar
Hitchy
Big Dorifto
Posts: 79
Joined: Fri May 29, 2009 3:59 pm
Location: Melbourne

Post by Hitchy »

That looks Sick, great job! :beer
When you hit the tree between the headlights that’s understeer. When you hit the tree between the tail lights that's oversteer!
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

thanks champ!
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
User avatar
KNIGHT RYDER
Big Dorifto
Posts: 94
Joined: Fri Jun 10, 2011 8:13 pm
Location: land of the long exhaust cloud

Post by KNIGHT RYDER »

I wouldnt go smaller they look primo,car looks so tidy i wouldnt add anything to it,what offset and did they need spacers?
Top
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

hey mate no spacers, +6 front and rear, 10's on the back and 8.5's front. Only gripe about the overall diameter is they fill the guard so much its hard to drop down even with pumping an inch each side.
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Top
Post Reply

Return to “Show And Go”

Who is online

Users browsing this forum: No registered users and 20 guests