help with water system

For all your twin cam conversion questions and hints
stariontron
I like starions more
Posts: 198
Joined: Thu Jan 08, 2004 11:12 pm
Location: auckland, NZ

Post by stariontron »

dwlee wrote:The holes in a dohc block I have in the shed are 6mm. Also, note the oil inlet is on the exhaust side.
oh ok, that wasnt the impression i got from the pictures. so the oil feed is on the bolt hole closest to the thermostat. how far up is the gallery?
dwlee
[P] Plates
Posts: 34
Joined: Tue Sep 26, 2006 10:15 am
Location: Auckland NZ

Post by dwlee »

The oil feed is on the rear head bolt hole on the exhaust side of an evo 1, 2, 3 head. If I remember correctly the gallery is about 20mm up, but don't quote me on it. If you have a look you should be able to see the opening for the gallery.
stariontron
I like starions more
Posts: 198
Joined: Thu Jan 08, 2004 11:12 pm
Location: auckland, NZ

Post by stariontron »

ok cool thanks. i'll rip the head and get it sorted as soon as i can bring myself to undo all my work (and it stops raining)
avandull
Mine is bigger than yours
Posts: 346
Joined: Thu Aug 12, 2004 4:49 pm
Location: Hobart

Post by avandull »

Back to your original question.

This is one option for a rear water outlet. I have made up a pipe out of aluminium from the rear outlet on the head, note the air bleeder fitting.(brass fitting at the highest point)

Image


The pipe leads to a mid 80's corolla thermostat housing(AE82 fwd), Before it leads to the top radiator tank.

I have used the VR4 water pump, I made the pipe so that I can put the bottom radiator hose on. I still have a heater and thermostat, that is the function of small black pipe going below the exhaust ports. It feeds the low pressure side of the heater core, and also goes on to the bypass port on the thermostat housing. This is so that water circulates past the thermostat before it opens.

Image

Image

Image

Image

Thanks Mr Bender for the head, It appears again.
Agatha the ugly Starion
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

Avandull, what did you use to blank the lower timing case where the engine mount used to be?
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
OLD FART
Austarion Occupant
Posts: 3448
Joined: Sun Jun 19, 2005 1:34 pm
Location: Brisbane

Post by OLD FART »

I used a bit of flat black plastic cut to shape and silicone :)
I've had mine since 03 07 92
85 JB 2323cc DOHC 4G63
THE OLDER I GET THE FASTER I WAS
GROWING OLD IS MANDATORY GROWING UP IS OPTIONAL
avandull
Mine is bigger than yours
Posts: 346
Joined: Thu Aug 12, 2004 4:49 pm
Location: Hobart

Post by avandull »

I cut the engine mount flush with the rubber surround and painted it black
Agatha the ugly Starion
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

Nicely done, looks professional.
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
fugazi
Enthusiast
Posts: 716
Joined: Thu Oct 02, 2008 10:30 pm
Location: Stockholm, Sweden
Contact:

Post by fugazi »

enthuzed wrote:...looks professional.
I think the head looks ported... exhaust anyway... let's see some more ayiii???!!! :D
Image
stariontron
I like starions more
Posts: 198
Joined: Thu Jan 08, 2004 11:12 pm
Location: auckland, NZ

Post by stariontron »

sorry guys one more question, with the oil feed hole, do i need to drill down into the block under that hole too? or will the 12mm head stud sitting in there not block it like it does with the head hole. cheers
avandull
Mine is bigger than yours
Posts: 346
Joined: Thu Aug 12, 2004 4:49 pm
Location: Hobart

Post by avandull »

Regarding the oil feed, dont drill in to the block.
Agatha the ugly Starion
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests