Clean... Still no polish

Mick · Post by **Mick** » Sat Apr 23, 2011 3:13 pm

Finally gave it a wash and shammy... still no polish after respray but she looks ok. Never remember to stop in and get the right polish...
Put decent dunlop 245s on the back to clear guards but still having slight clearance issues... So many little things to iron out. Ideally it will sit about 50mm lower in the back but need more camber. Thanks fro looking will post more photos as it comes along if theres interest

jk · Post by jk » Sat Apr 23, 2011 3:22 pm

Looks very impressive, well done.

Wheel diameter's a little big for my tastes but still a very sharp fitment.

Post by **TOMSUN** » Sat Apr 23, 2011 3:26 pm

WOW... Paint, Wheels & Tint look great.

Remind us what motor combo / mods your running

Mick · Post by **Mick** » Sat Apr 23, 2011 3:33 pm

JK it turns out not my taste either. without bodykit its still a bit wide to run low. but cant exactly sell them on the side of the road now :?

Tomsun, just a 20g, motec, a good tune at 18 psi made 205 kw atw and 550nm atw,big fronty, acl head gasket and studs... nothing major. the engine bay photos are on a slightly older thread.

avandull · Post by **avandull** » Sat Apr 23, 2011 4:46 pm

Looks good Mick. How did the putting the rear suspension back together? Does it sit at the height you were after?

Mick · Post by **Mick** » Sat Apr 23, 2011 4:58 pm

yeah mate its spot on, as i said it cant go any lower as it rubs., will sell them wheels if i ever get the chance!

redzone · Post by **redzone** » Mon Apr 25, 2011 10:00 am

yeah phil pumped the guards on his JA to make them fit...

Mick · Post by **Mick** » Mon Apr 25, 2011 3:35 pm

yeah dave i remember he mentioned that, without a bodykit it'd be much easier, and its been pumped an inch each side already.

NXTIME · Post by **NXTIME** » Mon Apr 25, 2011 4:53 pm

Car looks great, Mick. The only thing I would add is the factory rear wing kit***. :beer

Mick · Post by **Mick** » Mon Apr 25, 2011 6:44 pm

thanks mate, appreciate the kind word, not really a fan of the factory spoiler on cars that arent real low, if i can get some more camber on the back and wind it down on the coil overs its an option...

NXTIME · Post by **NXTIME** » Mon Apr 25, 2011 6:51 pm

***Edited: I meant 3-piece rear wing

Mick · Post by **Mick** » Mon Apr 25, 2011 6:59 pm

yeah i guessed that mate :)
you're a fan then? will check out some other black ones with em

JDSTAZ45 · Post by **JDSTAZ45** » Mon Apr 25, 2011 10:34 pm

NXTIME wrote:***Edited: I meant 3-piece rear wing

There's nothing wrong with a good condition rubber spoiler and the Starion turbo decal on the back. Looks great esp. on the dark coloured stazzas.

Dirty Sanchez has a good one up for grabs!

Also, is that rear pod sideskirt made by Advanced spoilers? Great look imho!

Mick · Post by **Mick** » Mon Apr 25, 2011 11:07 pm

well spotted mate,
they were custom made by the guys that did the paint and panel, it does look silly having 10' wide rears out that far with a standard bumper.

advanced spoilers ripped me off, the front was 70mm too wide and the side skirts 50 too short.
didnt want to know about it. be careful.

hoongirl · Post by **hoongirl** » Wed Apr 27, 2011 1:25 pm

Looks great :beer

Austarion

Clean... Still no polish

Clean... Still no polish

Who is online