Baskerville raceway 17/3/2011 RaceChrono

Display your ride and post power figures, dyno runs, drag and circuit times.
Post Reply
avandull
Mine is bigger than yours
Posts: 346
Joined: Thu Aug 12, 2004 4:49 pm
Location: Hobart

Baskerville raceway 17/3/2011 RaceChrono

Post by avandull »

I bought a new RaceChrono GPS lap timer. Check out the footage.

http://www.youtube.com/watch?v=kTtWT5mVymQ

Here is a few slower laps, this RX7 got past me off the start, but was slower around corners.

http://www.youtube.com/watch?v=YQJmZkuRnzU
Agatha the ugly Starion
fugazi
Enthusiast
Posts: 716
Joined: Thu Oct 02, 2008 10:30 pm
Location: Stockholm, Sweden
Contact:

Post by fugazi »

You need some stickier tires mate! :D
Very nice!
Image
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

Love the interface. Was it easy to setup? How about working it together with the video, does it take long?
Cool maplight, do you use it much?
If you do, may I suggest an LED globe for it...it's brighter, doesn't get hot and uses less power.
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
avandull
Mine is bigger than yours
Posts: 346
Joined: Thu Aug 12, 2004 4:49 pm
Location: Hobart

Post by avandull »

The Racechrono produces a log file. The RacechronoAVI program takes the log file and produces an avi of the speedo and position on the track. Then you need a video editing program to overlay the speedo avi with the video file from your camera.
So the whole process takes some time and there are a few steps.

I don't use the map light much
Agatha the ugly Starion
enthuzed
Austarion Occupant
Posts: 3578
Joined: Tue Apr 06, 2004 1:21 pm
Location: Melborno
Contact:

Post by enthuzed »

Avandull, can you spell out the steps involved please and what sort of time each step takes.
Also, can you use the GPS unit it comes with as a normal GPS navigational device?
Reduce fuel costs by 15-20% & cut emissions by 1/3rd...
Increase engine performance & prolong engine life...
How?
Click the website button below & watch the 3 minute video.
Mick
Enthusiast
Posts: 643
Joined: Sun Mar 12, 2006 1:37 pm
Location: Hobart, Tas

Post by Mick »

sick al!

mate some fat slick 17's with a bit of sidewall and you'd be under a minute!!
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
compressor
Mine is bigger than yours
Posts: 315
Joined: Mon Apr 12, 2004 9:33 pm
Location: GEELONG

Post by compressor »

GOOD footage sounds like mine :)
Post Reply

Who is online

Users browsing this forum: No registered users and 26 guests