Sounds good! Greg has posted on the forums so im sure he's seen this thread. He probably can't get leave approved.NXTIME wrote:I have scoped out Thirroul and there are a few places to get some food, however, there isn't much parking for a bunch of cars at the one place. So, I have found another well-known hotel just before Thirroul, in Austinmer called the Headlands Hotel. It is an iconic hotel and has a very good (seafood) restaurant and is located high on the hill, has plenty of parking and some great views.
Next Sydney Cruise - 17th April - Austinmer
- Cookiemonster
- Mother Goose
- Posts: 3177
- Joined: Thu Jan 08, 2004 4:33 pm
- Location: Sydney
- Cookiemonster
- Mother Goose
- Posts: 3177
- Joined: Thu Jan 08, 2004 4:33 pm
- Location: Sydney
So I better bring the tripod then
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
Hoonie, I suspected Jim's was where you had in mind and I did scope out the Mary St area.
I also read about the Headlands Hotel and the fact that it is destined for demolition to make way for some apartments. So, it's probably the last chance to go there. Location and setting look good, too. Plus, I think the fact that we have 9 or 10 people makes the pub a little more attractive seating-wise.
We can also then drive down to the beach carpark at Mary St Thirroul afterwards. :beer
I also read about the Headlands Hotel and the fact that it is destined for demolition to make way for some apartments. So, it's probably the last chance to go there. Location and setting look good, too. Plus, I think the fact that we have 9 or 10 people makes the pub a little more attractive seating-wise.
We can also then drive down to the beach carpark at Mary St Thirroul afterwards. :beer
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
-
- I like starions
- Posts: 108
- Joined: Fri Jun 18, 2010 9:36 pm
- Location: Camden
- starion4me
- I've been here before
- Posts: 215
- Joined: Fri Jan 09, 2004 6:11 pm
- Location: Sydney
this one fits - bigger bore so less pedal needed and bolts straight up and is only around $130 newNXTIME wrote:Aaron, Brake Master Cylinder Assembly Part # is MB534700
However, Mal has bought a new brake master cylinder from the USofA as I believe they have plenty available there.
Made by Nabco Japan.
master cylinder is JB1775 off 2/95 on nissan patrol
rd28t turbo 2.8l 4x4
26.99mm
tokico
Chrysler Conquest (SOLD)
270.6 Kw (362 HP) @ the wheels
270.6 Kw (362 HP) @ the wheels
- starion4me
- I've been here before
- Posts: 215
- Joined: Fri Jan 09, 2004 6:11 pm
- Location: Sydney
Russ didnt give you any issues?
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
- Cookiemonster
- Mother Goose
- Posts: 3177
- Joined: Thu Jan 08, 2004 4:33 pm
- Location: Sydney
Who is online
Users browsing this forum: Bing [Bot] and 0 guests