Who has a 5 stud narrow and is looking for pimp wheels?

redzone · Post by **redzone** » Tue Jun 29, 2010 10:26 pm

found these on j-imports:

Work Meister S1
114.3x5
17x8 +13
17x9 +15
$2200 (ETA SEPT)

PERFECT SIZES!

someone grab em :)

JD_Stazza_Brendan · Post by **JD_Stazza_Brendan** » Wed Jun 30, 2010 1:32 am

*cough* Bao *cough*

NachoMan · Post by **NachoMan** » Wed Jun 30, 2010 2:38 am

:drool:
I'd be on these like flies on shit if I wasn't planning to sell my GSR-V.

thrash · Post by **thrash** » Wed Jun 30, 2010 4:28 pm

if you have a 5-stud setup you can sell me, i'll come up with the money by september :D

redzone · Post by **redzone** » Wed Jun 30, 2010 6:15 pm

with those sizes and offsets, the silvia boys will have nabbed them by the end of the week. they've only just been listed in the last couple of days...

thrash · Post by **thrash** » Wed Jun 30, 2010 11:23 pm

ahh sorry red, i thought YOU were getting these around september. my apologies, i misread your post :(

redzone · Post by **redzone** » Mon Nov 29, 2010 8:46 pm

man, these are still available, i CANNOT believe it!! someone grab em!

thrash · Post by **thrash** » Mon Nov 29, 2010 11:49 pm

somebody buy my cars.. they are good cars!! then i'll have the cash for these babies

Post by **TOMSUN** » Tue Nov 30, 2010 10:22 am

DAMN!!! They are perfect sizes... !

Dave, how much to convert to 5 stud? and do you have all the parts avaliable?

I thought I was lucky to find my Weds 3-piece mesh rims... They are 17x7.5+16, 17x8.5+16 and they are 9-hole :)

jk · Post by jk » Tue Nov 30, 2010 7:32 pm

Some very similar SSR wheels on a flatty (maybe slightly less +offset than the Works). The Works would look just as good, car below is one of the most visually inspiring Starions I've ever seen.

redzone · Post by **redzone** » Tue Nov 30, 2010 10:57 pm

TOMSUN wrote:DAMN!!! They are perfect sizes... !

Dave, how much to convert to 5 stud? and do you have all the parts avaliable?

I thought I was lucky to find my Weds 3-piece mesh rims... They are 17x7.5+16, 17x8.5+16 and they are 9-hole :)

5 stud parts are usually between $500 and $800, comprising rear spindles, front hubs, F & R discs & caliper brackets from an 86/87 widebody, this all bolts easily into any aussie starion and gives you a 1 inch brake disc upgrade at the same time. offset requirements are unchanged.

i'm just about to get some more 5 stud bits over from the states, i have a mate after a set..

NXTIME · Post by **NXTIME** » Wed Dec 01, 2010 2:53 am

they bolt to flatty rear axles?

That red flatty looks very nice and similar to Mals GSR-V.

interesting rear wing too

enthuzed · Post by **enthuzed** » Wed Dec 01, 2010 2:49 pm

Looks like the arches have been massaged!

1320ft · Post by **1320ft** » Wed Dec 01, 2010 5:58 pm

OT, that Flatty is just Fu*ken sex!

redzone · Post by **redzone** » Wed Dec 01, 2010 9:20 pm

NXTIME wrote:they bolt to flatty rear axles?

That red flatty looks very nice and similar to Mals GSR-V.

interesting rear wing too

yes. the splines on the rear spindles are the same as long as you dont get the 6 bolt type spindles, you just use the early (ie aussie) 4 bolt flange on the new USA 86/87 widey rear spindles and it all bolts together..

i reckon mal should buy these works for the GSR-V, they're spot on and a suitable colour!!!!

Austarion

Who has a 5 stud narrow and is looking for pimp wheels?

Who has a 5 stud narrow and is looking for pimp wheels?

...

Who is online