ill get a moderator to try ban you :)MR Bender wrote:yer im trying to load it!iXNAY wrote:dyno sheet or ban!
my car is not DONE and probably never be!
give it a few months and im sure the twitch for more power will arise and knowing its so easy to acheive by just turning up the boost :) the boost devil will get the better of you!MR Bender wrote:im happy now! i dont think it will pop.iXNAY wrote:well atleast if you pop it you can just go a forged bottom end and be happy :)
SR20 powered starion what have I done..... :P
in the words of hancock.. good job :beer
what's the rev limit on the stock vr4 motor? is it 7k?
what's the rev limit on the stock vr4 motor? is it 7k?
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
-
MR Bender
- Enthusiast king
- Posts: 754
- Joined: Sun Nov 11, 2007 8:01 pm
- Location: Perth Western Australia (SOR)
i have mine set at 7250rpm but my old vr4 had some chip that let it go to 8kthrash wrote:in the words of hancock.. good job :beer
what's the rev limit on the stock vr4 motor? is it 7k?
Bite my shiny metal ass!!!
Russell Coight: Some of the animals are nocturnal, so the best time to see them is at night. Only you can't see them, because it's dark.
Russell Coight: Some of the animals are nocturnal, so the best time to see them is at night. Only you can't see them, because it's dark.
8k on a stock motor? how did it handle it?
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
-
redzone
- racking my brains
- Posts: 5900
- Joined: Thu Oct 06, 2005 10:46 pm
- Location: sunshine coast qld
- Contact:
thrash wrote:8k on a stock motor? how did it handle it?
stock rods are pretty damn strong! and it's a mitsu not an SR hahahahahaha
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q
www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q
www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
-
MR Bender
- Enthusiast king
- Posts: 754
- Joined: Sun Nov 11, 2007 8:01 pm
- Location: Perth Western Australia (SOR)
well it was a waste because it stoped making power after 6500k but there were times i was using it and it seams fine.i would be more worred in spinging a bearing than bending a rod.thrash wrote:8k on a stock motor? how did it handle it?
355bhp is about 264kw at the wheelsfugazi What kW@wheels? You didn't measure at the crank, or?
it was measured in horsepower at the wheels.
at the crank its about 350kw
Bite my shiny metal ass!!!
Russell Coight: Some of the animals are nocturnal, so the best time to see them is at night. Only you can't see them, because it's dark.
Russell Coight: Some of the animals are nocturnal, so the best time to see them is at night. Only you can't see them, because it's dark.
Who is online
Users browsing this forum: No registered users and 1 guest