My new Widey : BRUTUS

enthuzed · Post by **enthuzed** » Sun Jan 24, 2010 1:00 am

Yep, it was Tomsun, particularly the opened up areas of the radiator support panel.

redzone · Post by **redzone** » Sun Jan 24, 2010 9:56 am

TOMSUN wrote:
redzone wrote:
Sargeant_Khan wrote:what kind of figures bounced up on the run in tune?
150hp atw at 6 psi at 4500rpm, without doing ignition maps..

ps what do you want pics of enthuzed?
I think it was the Intercooler Pipework and clearances? (We'll that was I was keen to see :D

thats what ixnay was keen to see LOL

incredibly hard to take a pic of the rad support area as it's so dark and everything just blends in, i've tried a few times with my 5mp camera, getting a new one soon so will have another go for ya's...

iXNAY · Post by **iXNAY** » Sun Jan 24, 2010 12:19 pm

yeah im just keen to see what has been done for the piping

groupAralliart · Post by **groupAralliart** » Fri Jan 29, 2010 9:11 pm

a pic:

MR Bender · Post by **MR Bender** » Fri Jan 29, 2010 9:12 pm

:drool:

WANTSOM · Post by **WANTSOM** » Sat Jan 30, 2010 1:53 am

Love the fat guards at the rear........... highlighted by wheels that fully fill the fuckers :drool:

looking very cool Dave and Steve.

redzone · Post by **redzone** » Sat Jan 30, 2010 8:58 am

do you like my D.O.T. style ride height checking apparatus? LOL

iXNAY · Post by **iXNAY** » Sat Jan 30, 2010 9:15 am

is that a sledge hammer?

greenstaz82 · Post by **greenstaz82** » Sat Jan 30, 2010 10:50 am

lookin good , would be nice to see this car in the flesh when finished .i hope everything runs smoothly for ya with not to many major problems .

WANTSOM · Post by **WANTSOM** » Sat Jan 30, 2010 1:27 pm

The man said it was a DOT approved ride height tester so just leave it at that. The same tool is also called a body alignment tool, a drift punch and I've even seen them called clearance indicator/adjuster.

Every decent workshop has one.

OLD FART · Post by **OLD FART** » Sat Jan 30, 2010 1:52 pm

Sure looks like a heavy duty knockometer to me :)

Steve E · Post by **Steve E** » Sat Jan 30, 2010 3:22 pm

It looks like my fixit or fugit tool :D

Post by **TOMSUN** » Sat Jan 30, 2010 7:06 pm

What is the required ground clearance? I thought it was about 120mm?

redzone · Post by **redzone** » Sat Jan 30, 2010 7:55 pm

nah that's no hammer, it's a 105mm block of wood screwed to a inch by inch block of wood :) it's my ride height checker..

100mm is the lowest allowed clearance up here, other than brake backing plates..

no dramas as yet, only the need to adjust the clutch master cylinder's freeplay to achieve a good clutch height and release.. she's lookin sweet so far. ps those arias pistons are noisy when cold! cp/je/wiseco's are heaps quieter.. fine when it's warmed up of course.

thrash · Post by **thrash** » Mon Feb 15, 2010 8:51 pm

soo... tuned yet? power figure? more pics? :D

Austarion

My new Widey : BRUTUS

Who is online