microtech lt8s for sale to suit magna 2.6 ignition setup.

Got something to sell? Looking for a rare Starion part? Got something bust that needs replacing? then this is your place!
Post Reply
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

microtech lt8s for sale to suit magna 2.6 ignition setup.

Post by 13bsigma »

I bought this ecu for my sigma about 7 months ago for $500 and spent $350 getting it calibrated to suit a magna ignition setup. so basically you can put the 2.6L engine into your sigma or starion with the throttle turned around and have full control over the tuning of the fuel and ignition. i can supply the wiring loom too if you want. this computer is in full working order as the guys at microtech went over it when re-calibrating it.

I'm after $450 with it with the wiring loom.

I also have a hand controller for it that i bought brand new. hasn't even been out of bubble wrap. i bought for 300. will sell for $200.

I can supply pics if needed, but will take a few days as i just took pics on my friends camera and will have to get them emailed to me then on to you if needed as i don't have a camera myself.
tri26t
I love starions
Posts: 484
Joined: Fri Nov 26, 2004 7:19 pm
Location: townsville

Post by tri26t »

Hi, it is laptop enabled yes ?????
and is there a cable for laptop ?????
what version is it ????????
has it only been set for N/A tune ????
Fuel map ?????

Pics to tri26t@gmail.com

Cheers: Phil.
TORQUES-CHEAP.
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

Hi Phil, I'm not sure if it is lap top enabled? there is a cable with the hand controller, but not with the ECU.
It is version 1.0.
It was setup to suit a magna distributor, so you can tune it for boost.
It also has a map sensor, so no air flow meter is needed.

Hope that helps.

Dane
airbats801
Enthusiast
Posts: 737
Joined: Wed Feb 02, 2005 2:46 pm
Location: oregon, USA
Contact:

Post by airbats801 »

so can you actually interface with this ecu on a laptop and tune or do you need the hand controller?
'78 Colt cp, 80 challenger "scorpion" 5spd g54bt conversion almost complete, '80 plymtouh arrow "might max" , '90 mitsu terror van "spacewagon"
80's Hero
Image
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

Ok, i just called the guys at microtech and they stated that it is laptop enabled. apparently thats what the 'L' stands for in LT-8s.

So that answers that question for all interested. :)
airbats801
Enthusiast
Posts: 737
Joined: Wed Feb 02, 2005 2:46 pm
Location: oregon, USA
Contact:

Post by airbats801 »

might have to takwe this off your hands. I gotta go look up the specs. I sold my haltech e11v2 a while back, this may be a better than no stand alone at all deal.
'78 Colt cp, 80 challenger "scorpion" 5spd g54bt conversion almost complete, '80 plymtouh arrow "might max" , '90 mitsu terror van "spacewagon"
80's Hero
Image
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

Yeh sure, just let me know when you know the specs. :beer
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

Bump.


I will be putting on ebay very soon. anybody interested? Make me a reasonable offer.
tri26t
I love starions
Posts: 484
Joined: Fri Nov 26, 2004 7:19 pm
Location: townsville

Post by tri26t »

is this a full loom or piggy backed (wired into ts.tr factory -fagna-loom)
Im gonna need a full loom, thanx again,
Cheers: Phil.
TORQUES-CHEAP.
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

Its a full wiring loom. and total stand alone ECU.
Basically, get a 2.6L engine, use a magna manifold and distributor and tune. i also have a magna manifold if anyone needs one. for $200. to suit RWD with injectors (standard)
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

Just as a ref: The LT stands for Laptop.
User avatar
Lunacy
nearly postwhore
Posts: 1355
Joined: Fri Jul 22, 2005 3:31 pm
Location: Land of Confusion

Post by Lunacy »

Is this able to be reconfigured to run a twincam 4g63?
Image
13bsigma
Dorifto!
Posts: 53
Joined: Sun Apr 20, 2008 9:39 pm
Location: Sydney

Post by 13bsigma »

No. you cant re-configure the LT8 series anymore. So it has to suit an astron 2.6.
leoca
I've been here before
Posts: 205
Joined: Sat Nov 03, 2007 8:42 am
Location: BRISBANE

Microtech

Post by leoca »

Is this still for sale mate ?.

john
Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests