Page 1 of 4

Sherminator's Staz ::Update::

Posted: Fri Aug 27, 2004 11:17 am
by MrGenius
The engine is out cause for some reason it didnt want to run with 700ml of oil. Seized oil pump and the balance shaft aint moving in a hurry.

Image

Pulled the engine down also to have a geezer of what was in there.

Image

Changed the springs over to some lowered ones so it dont look so gay with the 18's on it.

Image

New steering wheel too as the old one got farked when the yobbos tried to flog the car.

Image

Plenty more to come as we piece it all back together and i remove all the rice when he's not looking

Re: The Sherminator's Staz pulled down [www.18u]

Posted: Fri Aug 27, 2004 11:45 am
by Alspos
MrGenius wrote:Plenty more to come as we piece it all back together and i remove all the rice when he's not looking
Like the headlight switches?

Posted: Fri Aug 27, 2004 1:13 pm
by LxS
Nice car, are you taking the huge sticker off the front too?

BTW: How much did your springs set you back if you dont mind me asking, PM if it's private. Can you get discounts :D

Re: The Sherminator's Staz pulled down [www.18u]

Posted: Fri Aug 27, 2004 1:55 pm
by MrGenius
Alspos wrote:
MrGenius wrote:Plenty more to come as we piece it all back together and i remove all the rice when he's not looking
Like the headlight switches?
Dont worry we have all payed him out about his replacement headlight switches :D The old ones flew out the window while driving through the M5 tunnel when he switched them off rofl

LxS
Sticker will most likely be removed in favour of one of mine :D

Springs for starion 40mm lowered $270 for all 4 plus postage PM me if ya interested :)

Posted: Fri Aug 27, 2004 5:32 pm
by Cookiemonster
What types of missiles can you launch from that dash?

Posted: Fri Aug 27, 2004 9:09 pm
by MrGenius
rofl

Posted: Sat Aug 28, 2004 2:15 am
by decoy
rofl

sweeeeeeet, missile switches :P pow pow! *whisltels* BOOOOOOM

Posted: Sat Aug 28, 2004 9:14 am
by LxS
Very Interested -

But I have a problem, my starion has 'choped' springs curtousy of the the previous owner, and I need new springs all round but dont have a clue how low it has been dropped ?

Posted: Sat Aug 28, 2004 5:14 pm
by www.18u
the ones stiffler supplied (mr genius) are 1 1/2 inch front 2inch rear if not low enough for you you can get them reset very cheap but they are set at that height id say cause it handles best there. :wink: You guys can laugh at my light switches but think of this it cost me $30 to fix compared to $330 for the genuine ones

Posted: Sun Aug 29, 2004 11:21 am
by MelbStazz
My switches died as well, i pulled the dash apart got the switches out, and glued them back together. 18 months down the track and they're still good as new. The missle switches give it a unique look.
:D

Posted: Sun Aug 29, 2004 10:14 pm
by MrGenius
LxS wrote:Very Interested -

But I have a problem, my starion has 'choped' springs curtousy of the the previous owner, and I need new springs all round but dont have a clue how low it has been dropped ?
Take a measurement from the centre of your wheel to the guard all around and put the measurements up here then if someone with a stocker height one could do the same u can figure it out :)

Posted: Tue Aug 31, 2004 6:46 pm
by Will
My ride height is 320mm rear, 305mm front. That's wheel centre to guard lip. Can someone post their stock ride heights please. I'm interested to know how much drop my car has.

What brand are those springs MrGenius? and do you have a ride height measurement for them when fitted?

Posted: Tue Aug 31, 2004 7:50 pm
by Chris 83JA
very rough measurements:
355 back
335 front

in the dark, with a torch and a ruler

Posted: Wed Sep 01, 2004 3:14 pm
by MrGenius
Will wrote:What brand are those springs MrGenius? and do you have a ride height measurement for them when fitted?
They are Dobinsons springs.

I can check the heights but they wont be very accurate as the car hasnt moved so the springs wont have settled, plus there is no engine in the car so the front is sky high :) I'll get a few of the boys to get in the engine bay and make 4G63 noises and measure the height.

Posted: Sun Sep 19, 2004 11:38 am
by MrGenius
Just waiting for the forgies to come then we can put the engine back together and start bolting on all the goodies :)

For those who wanted the sticker removed

Image

And ...

Image