1320ft's 2.3L Strip Warrior, Cage is in PG8
I actually picked up the box second hand from a reliable seller.
But Norm at Northmead Auto's will check it over and after we have dyno'ed the car, the converter will come out and be given to Slingshot to be checked.
The box allready has the 6 cyl input shaft and clutch packs installed. Plus has been manualised and reverse pattern.
But Norm at Northmead Auto's will check it over and after we have dyno'ed the car, the converter will come out and be given to Slingshot to be checked.
The box allready has the 6 cyl input shaft and clutch packs installed. Plus has been manualised and reverse pattern.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
Tossing up between these two atm, because I may just go straight to the Live rearend to save mucking around.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
nice one 1320 thats an awesome find second hand!
any idea what stall level you'll put in?
any idea what stall level you'll put in?
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Not yet.
Stall speed is something that will depend on final diff ratio, cam profile etc.
Stall speed is something that will depend on final diff ratio, cam profile etc.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
This is the diff that will be going in.
It is only a Borg Warner, but its got some goodies inside it that has allowed it to run deep into the 8 sec zone.
It is only a Borg Warner, but its got some goodies inside it that has allowed it to run deep into the 8 sec zone.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
nothing wrong with that diff mate!
just heaps wrong with the cars they came out in!
having said that now that their potential is being tapped there are vl's in the 8's still running them :beer
how much you gonna shorten it?
just heaps wrong with the cars they came out in!
having said that now that their potential is being tapped there are vl's in the 8's still running them :beer
how much you gonna shorten it?
FS: Ford 302ci Windsor. Race prepped block, Clevite bearings, ARP fixings, Hypertectic pistons, nitrided rods, knife edged crank, Gilmer drive, chrome moly rings, Yella Terra stage 3 heads, manly valves, Comp cams 294* solid roller, YT roller rockers, Funnelweb manifold, 2 inch spacer, Proform 830cfm carb, K&N 10" stack, ICE ignition. - 0437900210
Bar work has been picked up and is ready to notch and weld in.
I couldnt believe how quick they turned it around. Had the call back within 24hrs saying it was ready to pick up.
Its a behind the dash kit, 6 point in Mild Steel.
I couldnt believe how quick they turned it around. Had the call back within 24hrs saying it was ready to pick up.
Its a behind the dash kit, 6 point in Mild Steel.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
So I am at somewhat of a crossroads today.
After spending the last two days out at Superlap I am somewhat tempted to put a good IRS setup back in the car, get a manual and set the car up to do both drags and circuit racing. Obviously via auto back in when I go drag racing and manual for circuit.
After spending the last two days out at Superlap I am somewhat tempted to put a good IRS setup back in the car, get a manual and set the car up to do both drags and circuit racing. Obviously via auto back in when I go drag racing and manual for circuit.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
- Sargeant_Khan
- Enthusiast
- Posts: 673
- Joined: Thu Dec 16, 2004 9:31 pm
- Location: Ipswich
Stay the course... Keep it as a drag car. :D1320ft wrote:So I am at somewhat of a crossroads today.
After spending the last two days out at Superlap I am somewhat tempted to put a good IRS setup back in the car, get a manual and set the car up to do both drags and circuit racing. Obviously via auto back in when I go drag racing and manual for circuit.
1985 JB Starion #157
sorry to pull a cliche on you, but i think that you will find that if you make it a jack of all trades, it will not master either.
having said that, time attack does look like awesome fun, doesn't it??
having said that, time attack does look like awesome fun, doesn't it??
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
- Sargeant_Khan
- Enthusiast
- Posts: 673
- Joined: Thu Dec 16, 2004 9:31 pm
- Location: Ipswich
No worries mate.Sargeant_Khan wrote:Aaron, while the cage piping is out of the car, would you mind weighing it all for me?
Cheers
Jay
Yes, I am still a drag racer at heart, I would like to be able to enjoy the car a little more than the occasional wed night, TnT & Jambo etc.
While I ponder over this, I have asked a CAMS scrutineer customer of mine, what extra bars would be required to be added to my cage, to run superlap.
The Forum Parts Guy
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
www.vibrantperformance.com for all your performance fabrication needs
IRS OUTLAW, 2.3L VR4 Powered X235 Drag Car
Here to run out of your life & take all your money!
Who is online
Users browsing this forum: No registered users and 34 guests