Thrash: Reincarnation
thanks guys!
Thanks Al, will look into that. I've looked at a couple of videos on youtube and it looks quite easy :beer
Thanks Al, will look into that. I've looked at a couple of videos on youtube and it looks quite easy :beer
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
thanks guys. I've bought a repair kit along with some fibreglass cloth, as the kit only comes with matt. Will see which one is easier to use.
Also got a roller on the way :)
4gpwr.. is hardener the same thing as 'catalyst' or MEKP?
Also got a roller on the way :)
4gpwr.. is hardener the same thing as 'catalyst' or MEKP?
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
so the first section i did was a complete disaster. I mucked up the hardener/catalyst measurement, and so after a week it still hasn't dried. Will have to scrub it off and start again. I assume acetone will make it all come off easily?
second attempt last night was a bit more fruitful. Fully dry this morning, so will sand it tomorrow or on the weekend. Pictures to come.
Don't know what experiences you guys have had with fibreglass, but i've learnt that the difference between chopped strand matt and cloth is that cloth is easier to shape when dry, but has less give when wet, while the matt that came in the repair kit is very stiff when dry, but will easily give and mold around complex surfaces when wet.
Thanks for the fibreglassing advice guys. I wouldn't have even bothered to attempt it if it wasn't for you folk :beer
second attempt last night was a bit more fruitful. Fully dry this morning, so will sand it tomorrow or on the weekend. Pictures to come.
Don't know what experiences you guys have had with fibreglass, but i've learnt that the difference between chopped strand matt and cloth is that cloth is easier to shape when dry, but has less give when wet, while the matt that came in the repair kit is very stiff when dry, but will easily give and mold around complex surfaces when wet.
Thanks for the fibreglassing advice guys. I wouldn't have even bothered to attempt it if it wasn't for you folk :beer
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
fiberglass
One tip with the hardener when mixing it add enough hardener till it starts producing heat
4Gs Rule
a little progress. the pieces of the bar are now joined together, with the middle opening lowered. Still needs to be sanded and smoothed more, and also the top edges of the mouth need to be fibreglassed, but not too bad for now.
I'm not entirely happy with the way it sits, as the top edge of the bar along the side doesn't match the side lines of the car, so i might lower the rear part of the bar a bit to try and match this up.
Also, the bar is actually quite heavy as it is, so once i've had a bit more practice fibreglassing, I will eventually try and make a mould of it and then a lightweight copy. But this will have to do until the rest of the car is put back together
I'm not entirely happy with the way it sits, as the top edge of the bar along the side doesn't match the side lines of the car, so i might lower the rear part of the bar a bit to try and match this up.
Also, the bar is actually quite heavy as it is, so once i've had a bit more practice fibreglassing, I will eventually try and make a mould of it and then a lightweight copy. But this will have to do until the rest of the car is put back together
quest wrote:don't try explaining that to her tho..... just leave. lolWANTSOM wrote:Personally, I find sloppy boxes very unsatisfying. I like them tight and taught to the point that if you dont have to push to get it in then its probably too old and time to get a new one :P
Who is online
Users browsing this forum: No registered users and 17 guests