Easiest way to get the stupid metal bits out of the hatch?

Technical questions and ideas regarding how your Starion looks inside and out, bodykits to stereos.
StarionBoy
i need to paint my car!
Posts: 374
Joined: Fri Jan 09, 2004 9:42 pm
Location: Ballarat

Easiest way to get the stupid metal bits out of the hatch?

Post by StarionBoy »

just wondering what the easiest way would be to get those stupid metal bolt things out of the hatch (u know the ones that hold the stock rubber wing on)... could grind the top off them but then the rest are left floating around in side the hatch.. and u cant really cut a hole in the end of the hatch to get them out cos its indented in a bit.. :?: :?: :?:
User avatar
Alspos
Flucking kwankers
Posts: 4107
Joined: Thu Jan 08, 2004 2:09 pm
Location: Melbourne
Contact:

Post by Alspos »

Tell me how you go. I have a spare hatch on cos I have to do the same to the original one. I assumed you'd have to pull it off the glass, empty them out and reattach.
The spare hatch has had the bolts removed and dropped inside. It's a good reminder on when you are turning, the bolts run from one side to the other inside it. If you drive in an "S" you can make a tune :D
Cam
c'mon change my thingy
Posts: 405
Joined: Thu Jan 08, 2004 3:48 pm
Location: Rosebud, Vic
Contact:

Post by Cam »

I believe it is possible to remove the little piece at the back, Then you could fibre glass over filling up the holes coz trust me, the previous owner bogged them up in my car, they all sunk looks shit.
pcuser51
I like starions
Posts: 141
Joined: Fri Jan 09, 2004 2:32 pm
Location: TASMANIA

Post by pcuser51 »

:D yes grind them off and get alarge magnet to draw them back through the holes then fiberglass the holes over, that how i did it :wink:
CHEERS ALAN
User avatar
Cookiemonster
Mother Goose
Posts: 3177
Joined: Thu Jan 08, 2004 4:33 pm
Location: Sydney

Post by Cookiemonster »

You can make a hole in the side of the fibreglass section using a drill. Then take the car for a drive and go hard around a corner and all the bolts and crap in there will roll right out.
NachoMan
nearly postwhore
Posts: 1589
Joined: Sat Jan 10, 2004 12:28 pm
Location: Perth (Morley), WA
Contact:

...

Post by NachoMan »

Hahahaha Al!
Did you notice my car making those same noises in the hatch when i was driving you around?
I have experienced those noises for many a year, but I have all but blocked it out. Until, of course, someone points it out to me again!
Bloody annoying really! :roll:
StarionBoy
i need to paint my car!
Posts: 374
Joined: Fri Jan 09, 2004 9:42 pm
Location: Ballarat

lol

Post by StarionBoy »

yeah same problem here too, i didnt think it would be that noticable, but it sure is, espeically going around round-a-bouts, on to the highway, anywhere where your doing a bit of speed and turning at the same time lol keep hearing all 5 of the little pricks rolling from one side to the other hahah :roll:
pcuser51
I like starions
Posts: 141
Joined: Fri Jan 09, 2004 2:32 pm
Location: TASMANIA

Post by pcuser51 »

:D Starionboy if you had a 3inch exaust you would not hear them :D :D :D :D :D
CHEERS ALAN
Chris 83JA
almost postwhore
Posts: 1015
Joined: Sat Jan 10, 2004 12:02 pm
Location: Ballarat, Victoria, Australia
Contact:

Post by Chris 83JA »

pcuser51 wrote::D Starionboy if you had a 3inch exaust you would not hear them :D :D :D :D :D
No, a 3" exhaust just rattles the rest of the car to pieces
StarionBoy
i need to paint my car!
Posts: 374
Joined: Fri Jan 09, 2004 9:42 pm
Location: Ballarat

..

Post by StarionBoy »

i have a 2.5 inch exhaust, doesnt help much tho.. need to open up one of the holes again and pour some glue/liquid nails in one corner then tip it on its side so they all stick in there lol
User avatar
MelbStazz
Enthusiast king
Posts: 866
Joined: Thu Jan 08, 2004 2:55 pm
Location: Melbourne

Post by MelbStazz »

i've just removed the standard rear spoiler on my ja, can the rear hatch piece be seperated from the glass?
would anyone have a workshop page on how it's done?
thanks
drew
:D
- el schmicko detailer -
User avatar
hcca
Enthusiast king
Posts: 884
Joined: Thu Jan 08, 2004 9:24 pm
Location: Brisbane
Contact:

Post by hcca »

StarionBoy
i need to paint my car!
Posts: 374
Joined: Fri Jan 09, 2004 9:42 pm
Location: Ballarat

dodgy

Post by StarionBoy »

you can do it the dodgy way :roll: get hold of a grinder and just grind the tops off all of the bolts and push them into the hatch then bog the holes up.. you do end up with a nice sound of the bolts rolling from one end to the other when you go around corners and stuff rofl although mine have seemed to stop lately.. havent heard it for a while... i bet it will start again tomorrow now i have said that :wtf:
User avatar
AXELR8
I love starions
Posts: 361
Joined: Sun Feb 29, 2004 6:01 pm
Location: Adelaide

Listen to cookie!

Post by AXELR8 »

Cookie is right. I just drilled out the fiberglass at the ends of the hatch and went for a drive. 20 mins later all but one fell out. it was sitting right on the edge of the hatch so just like jack horner, i stuck in my thumb and pulled out a.... bolt head. Well you know what i mean! :P
You think that's fast??? You got nothin' on Roger!!
User avatar
Eurotrash
I drive commando!
Posts: 75
Joined: Thu Apr 15, 2004 7:43 pm
Location: Christchurch NewZealand

Post by Eurotrash »

Now I know this post is a little old but. For anyone next time. Since I have just removed my rubber rear wing. I can comment with experience. Sort of. Instead of grinding, cutting, drilling you bunch of butchers! Why not just unbolt the thing from the hatch. Ummmmm!
as I did. I know I know, a part of a starion that the rest of the car wasn't built around. Amazing! Maye mine was a once off prototype that doesn't requrie a cutoff wheel on a grinder. but it looks the same as other ones I've seen.
Good Luck
Post Reply

Who is online

Users browsing this forum: No registered users and 4 guests