Page 1 of 2
FS: Starion Head Rebuilt, Ported and Polished $250 -Brisbane
Posted: Sun Jul 23, 2006 12:21 pm
by boosterboy
I have a Starion head that I rebuilt and had ported and polished. It is still wrapped in plastic (gladwrap) from when it was rebuilt. Also comes with a Turbo VRS kit minus valve stem seals etc that were used in the rebuild. I will post pictures of it this afternoon.
I am looking for $250 for the head including gasket set. Postage or courier can be arranged at extra cost.
Cheers
Chris
0431835953
Posted: Sun Jul 23, 2006 2:58 pm
by jakobsladderz
Is it a jet valve or non-jet valve head? Is it ready to bolt on (as in it's been checked for flattness, valves seated etc)? if it's ready to bolt on then i'll be first dibs..
Posted: Mon Jul 24, 2006 9:44 am
by TOMSUN
Pics? Bump
Posted: Sun Jul 30, 2006 1:26 pm
by boosterboy
The head was totally rebuilt, 3 angle valve grind, pressure tested and surface checked. The head was originally a Jet valve head but has been converted to non jet valve on request.
Anybody interested in pics pm me with an email address and i'll send them.
Sorry about the delays but with work i'm really busy.
Cheers
Chris
Posted: Sun Jul 30, 2006 3:45 pm
by TOMSUN
How do you convert a Jet Valve head to a Non Jet Valve head???
Posted: Sun Jul 30, 2006 4:59 pm
by jakobsladderz
I'll take back my previous dibs, I had a head hanging around at home that I got recoed in the meantime, couldn't wait... go for it tomsun..
Posted: Sun Jul 30, 2006 5:57 pm
by Junkers
TOMSUN wrote:How do you convert a Jet Valve head to a Non Jet Valve head???
Blanking valves or weld up the holes.
What type or 'stage' port has been done to it?
Posted: Sun Jul 30, 2006 8:51 pm
by logik
why are you selling a starion head with all that done to it for $250?
Posted: Sun Jul 30, 2006 9:22 pm
by boosterboy
I had all the work done by Northside Cylinder Heads in Geebung Brisbane. I have had a few heads done through them and get mates rates
. As I have no Starions anymore I have no need for the head and the reduced price.
The head was pressure tested, acid dipped and cleaned. Intake and Exhaust valves faced, Serdi 3 angle on intake and exhaust seats. Mild port to clean up inlet ports, exhaust ports around valve guides seriously ported. 4 exhaust valve guides were replaced. Jet valves welded and non jet valve rocker gear swapped over. ACL gasket kit included.
Chris
Posted: Wed Aug 16, 2006 12:04 am
by TOMSUN
boosterboy...
Is this still for sale?
Posted: Thu Aug 17, 2006 6:06 pm
by boosterboy
The head is still sitting here for sale
Posted: Thu Aug 17, 2006 8:25 pm
by gjgnz
Did you get the PM I sent?
Posted: Thu Aug 17, 2006 8:36 pm
by boosterboy
Yeah thanks but not really negotiable, $250. Also prefer an Australian buyer easier to deal with postage etc.
Posted: Fri Sep 01, 2006 10:40 pm
by boosterboy
bump anyone
...
Posted: Sat Sep 02, 2006 3:25 am
by bigmoz
where are the pics???
and what stage porting and polishing is it minimal or maximum????
do you know how much postage to melbourne is postcode 3079
bigmoz :pimp
. As I have no Starions anymore I have no need for the head and the reduced price.