FS: Wolf 3D Version 4 New in box.

Got something to sell? Looking for a rare Starion part? Got something bust that needs replacing? then this is your place!
Post Reply
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

FS: Wolf 3D Version 4 New in box.

Post by boosterboy »

Item: Wolf 3D Version 4
Item Condition: New in box
Reason for selling: Project is over :(
Price and price conditions: $1100 ONO ($1400 new with optional hand controller)
Location: Brisbane

The whole kit is still in the box with all manuals, looms and sensors as originally purchased. It hasn't been tuned to suit a starion yet or email: boosterboy@iprimus.com.au. Mobile 0431 654891.

Chris.
User avatar
logik
I love starions
Posts: 397
Joined: Tue Jan 13, 2004 1:47 pm
Location: bunbury, western australia
Contact:

Post by logik »

pm sent
gordonspec® racing
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

PROJECT IS OVER????
Nooooooooo!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! :cry:
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

Project is over just put the VR4 engine on hold.

Cheers.

Chris
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

Do you still have the Wolf3d?
Why dont you just use the stock ECU chipped up on the VR4?
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

I do still have the Wolf3D but I have someone interested in it right now. I was actually planning on running a 32bit Delco system. I have a Nissan Pulsar that uses the 16 bit version and have eprom burner and all software etc to burn Delco chips. I have a lot of programming knowledge with the Delco. I learnt the Delco to understand the Wolf3D, start with grade3 maths before going to calc and linear algebra 101.

I don't have access to a VR4 ECU etc plus I wanted to stay away from afm. My Starion used to get beaten by Pulsars :( till I got on boost anyway.

My plan is to start with MPI on my ported and polished SOHC head. Get it running properly. With 2 or 3 bar map sensor the puter will handle boost and I have found fully supported rom files for a 4 cylinder sohc mpi turbo from the States.

Any help getting my 4G63 wide block - Dohc conversion working properly is still gonna take some work and advice and lots of $$$$$$$$.

Cheers

Chris
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

I like the way your heading...and where did you get the EPROM burner from?
User avatar
BLOFLY
I like starions
Posts: 143
Joined: Sun Apr 24, 2005 10:14 am
Location: Brisbane

Post by BLOFLY »

The delco system would seem to be a great solution for an economical engine management system. what software and hardware are you planning on using? as I have a full VN comp and loom and was thinking about going down the same road.
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

If you are after a complete 4 cylinder loom to suit. I am wrecking a Holden Astra N13 right now. The car still starts etc. If you want loom or any other bits and pieces advice come on round.

Flav, Electronics Australia or Dick Smith both make Eprom burner kits. Priced around $120 for the kit which needs to be assembled. I used to build electronics for a living so no dramas with quality of assembly.

Factory ECU helps with insurance and nosy police, not necessarily from the Misti factory but hey. I have analysed a stock starion ECU they are primitive. Delcos in various forms have block learn memory BLM, meaning over time with information from all the sensors including oxygen sensor it can trim up its fuel maps. You can read these BLM figures and adjust the base program closer to where it should be. Boost is still going to cause a few issues but keeping a very close eye on O2 readings using a wideband sensor I shouldn't have any dramas.


Chris
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

Hey there.

I am willing to accept $1000 firm for the computer.

Derek, if you are still interested in the computer it's now $1000.

Cheers

Chris
User avatar
Starion VR4
almost postwhore
Posts: 1293
Joined: Fri Jan 09, 2004 5:08 pm
Location: Brisbane

wolf

Post by Starion VR4 »

SOLD :beer
Image

30PSI,2.4L! Wolf 3D Ver 4. VR4 Head.
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

To the man with the VR-4 engined fire breather lol. :beer

Chris
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

Who may that be?????
User avatar
boosterboy
Dorifto!
Posts: 61
Joined: Sun Jul 25, 2004 6:12 pm
Location: Brisbane

Post by boosterboy »

Who mentioned it was sold?
;-)

Chris
flav
Austarion Occupant
Posts: 3374
Joined: Thu Apr 15, 2004 9:57 pm
Location: Melbourne

Post by flav »

Lucky Boy...!!!!
Post Reply

Who is online

Users browsing this forum: No registered users and 79 guests