Page 1 of 2
(SYD) WTD Non LSD Diff
Posted: Mon Apr 25, 2011 9:30 pm
by 1320ft
Yes, you read right, I want a NON LSD diff.
Am willing to do a swap with cash my way for my LSD (small) unit. But would prefer to just buy one.
Tell me what you got.
Posted: Mon Apr 25, 2011 10:03 pm
by JDSTAZ45
What! I can't believe what I'm reading.....
I've got a small 3.9 open diff to swap. Actually would prefer 3.54 to get better fuel economy!!
Also, have a large open centre from a JD diff. Just centre!
Take both with cash adjustment! :D :D
Posted: Mon Apr 25, 2011 10:38 pm
by enthuzed
How many open diffs do you want for the small LSD?
And how much cash? PM me.
Posted: Mon Apr 25, 2011 11:50 pm
by Sonic
Very interesting....P.M sent...
Posted: Tue Apr 26, 2011 6:50 am
by thrash
lol :beer
Posted: Tue Apr 26, 2011 8:44 am
by robert26t
Also got one here I wanna get rid of, if your interested give me a call.
Posted: Tue Apr 26, 2011 12:54 pm
by 1320ft
Replying to PM's in order of how they came in.
Just so people understand whats happening, I would rather blow up an open diff with a full spool etc, rather than an LSD that could be put to better use. Plus the ratio's arnt right for an auto.
Posted: Tue Apr 26, 2011 5:44 pm
by JDSTAZ45
What ratio were you after to use with your auto box? 3.9, 4.22 or 4.6??
In all honesty, wouldn't you be better off with one of the larger diffs for that extra toughness and reliability?
Posted: Tue Apr 26, 2011 7:02 pm
by Lummy
He's going to use a spool....you'll snap driveshafts well before you'll snap a spool. Best to run the smaller diff for less weight. Strength or reliability won't be an issue.
Posted: Tue Apr 26, 2011 8:50 pm
by redzone
if u get a spool made, get it with the large 6 bolt type half shafts, as the 4 bolt type ones WILL snap off inside the diff, mine did it running flat 13's...
Posted: Wed Apr 27, 2011 10:07 am
by TOMSUN
redzone wrote:if u get a spool made, get it with the large 6 bolt type half shafts, as the 4 bolt type ones WILL snap off inside the diff, mine did it running flat 13's...
So what diff is best to start with Mal's 3.9 Small or a 3.5 Large?
Do you need a large to run the 6 bolt half shafts?
Posted: Thu Apr 28, 2011 8:48 am
by redzone
3.5 or 3.9 large diff so you have the bigger crownwheel, and get the spool made to suit the 6 bolt type half shafts
Posted: Thu Apr 28, 2011 7:12 pm
by JDSTAZ45
redzone wrote:3.5 or 3.9 large diff so you have the bigger crownwheel, and get the spool made to suit the 6 bolt type half shafts
How would you connect the spline end from a 6 bolt shaft to an open large diff? Can this be swapped with a 4 bolt shaft? Wouldn't that become its weakest point again?
I say that because I'm not aware of any 88-89 open diffs! :?
Posted: Thu Apr 28, 2011 9:42 pm
by enthuzed
Might sound stupid but maybe it's an LSD behaving like an open. But surely he's had the back off it...
Posted: Thu Apr 28, 2011 11:54 pm
by redzone
JDSTAZ45 wrote:redzone wrote:3.5 or 3.9 large diff so you have the bigger crownwheel, and get the spool made to suit the 6 bolt type half shafts
How would you connect the spline end from a 6 bolt shaft to an open large diff? Can this be swapped with a 4 bolt shaft? Wouldn't that become its weakest point again?
I say that because I'm not aware of any 88-89 open diffs! :?
are u familiar with what a spool is Mal? basically it replaces the whole LSD or open type hemisphere.. it would be a full custom part for a starion so you could make it with whatever axle spline you want...