Page 1 of 2
Who has a 5 stud narrow and is looking for pimp wheels?
Posted: Tue Jun 29, 2010 10:26 pm
by redzone
found these on j-imports:
Work Meister S1
114.3x5
17x8 +13
17x9 +15
$2200 (ETA SEPT)
PERFECT SIZES!
someone grab em :)
Posted: Wed Jun 30, 2010 1:32 am
by JD_Stazza_Brendan
*cough* Bao *cough*
...
Posted: Wed Jun 30, 2010 2:38 am
by NachoMan
:drool:
I'd be on these like flies on shit if I wasn't planning to sell my GSR-V.
Posted: Wed Jun 30, 2010 4:28 pm
by thrash
if you have a 5-stud setup you can sell me, i'll come up with the money by september :D
Posted: Wed Jun 30, 2010 6:15 pm
by redzone
with those sizes and offsets, the silvia boys will have nabbed them by the end of the week. they've only just been listed in the last couple of days...
Posted: Wed Jun 30, 2010 11:23 pm
by thrash
ahh sorry red, i thought YOU were getting these around september. my apologies, i misread your post :(
Posted: Mon Nov 29, 2010 8:46 pm
by redzone
man, these are still available, i CANNOT believe it!! someone grab em!
Posted: Mon Nov 29, 2010 11:49 pm
by thrash
somebody buy my cars.. they are good cars!! then i'll have the cash for these babies
Posted: Tue Nov 30, 2010 10:22 am
by TOMSUN
DAMN!!! They are perfect sizes... !
Dave, how much to convert to 5 stud? and do you have all the parts avaliable?
I thought I was lucky to find my Weds 3-piece mesh rims... They are 17x7.5+16, 17x8.5+16 and they are 9-hole :)
Posted: Tue Nov 30, 2010 7:32 pm
by jk
Some very similar SSR wheels on a flatty (maybe slightly less +offset than the Works). The Works would look just as good, car below is one of the most visually inspiring Starions I've ever seen.
Posted: Tue Nov 30, 2010 10:57 pm
by redzone
TOMSUN wrote:DAMN!!! They are perfect sizes... !
Dave, how much to convert to 5 stud? and do you have all the parts avaliable?
I thought I was lucky to find my Weds 3-piece mesh rims... They are 17x7.5+16, 17x8.5+16 and they are 9-hole :)
5 stud parts are usually between $500 and $800, comprising rear spindles, front hubs, F & R discs & caliper brackets from an 86/87 widebody, this all bolts easily into any aussie starion and gives you a 1 inch brake disc upgrade at the same time. offset requirements are unchanged.
i'm just about to get some more 5 stud bits over from the states, i have a mate after a set..
Posted: Wed Dec 01, 2010 2:53 am
by NXTIME
they bolt to flatty rear axles?
That red flatty looks very nice and similar to Mals GSR-V.
interesting rear wing too
Posted: Wed Dec 01, 2010 2:49 pm
by enthuzed
Looks like the arches have been massaged!
Posted: Wed Dec 01, 2010 5:58 pm
by 1320ft
OT, that Flatty is just Fu*ken sex!
Posted: Wed Dec 01, 2010 9:20 pm
by redzone
NXTIME wrote:they bolt to flatty rear axles?
That red flatty looks very nice and similar to Mals GSR-V.
interesting rear wing too
yes. the splines on the rear spindles are the same as long as you dont get the 6 bolt type spindles, you just use the early (ie aussie) 4 bolt flange on the new USA 86/87 widey rear spindles and it all bolts together..
i reckon mal should buy these works for the GSR-V, they're spot on and a suitable colour!!!!