New Project - Lots of Pics AND Questions
Posted: Sat May 06, 2006 3:31 pm
So I got a new 88 Starion. Well not new :O. Great body except for the front bumper. No rust. Bad paint but the car hasn't ran for 6 years.
Problems I have faced.
Gas Tank rusted to hell.
In Tank filter ruined.
Fuel Pump ruined.
Fuel Lines all gummed up.
Lifters and jet valves bad.
Small hole in the Intake due to the corrosion.
So lets get to the pics. Here is the car the day I got it. And I got it for $150 usd.
NO it is not sitting on the bricks. I have a jack underthere. The brings are just saftey measure. Can never go wrong with a brick.
Here is the Turbo. What is that metal wheel in there? I never seen one. Somebody told me its a Frank Wheel?
Here is the top part of the Intake. What is that thing with all the wires coming off of it? The book says its an injection mixer but the picture isn't the same.
Same part but taken off
Intake Man. Pics of the corrosion
Small Hole
Head back from the shop
First Layer of JBWeld to fix the hole. You can see the rusted part to the left. The whole gas tank looks like that. Gonna have to have it boiled clean.
I'm currently still putting more layers of JB Weld over the damaged section of the intake. Then I will sand it down. Soon as thats done I will be putting the head back on. Intake and Exhaust, get the gas tank cleaned then start her up.
Parts bought and fixin to be replaced.
Water pump
Full Gasket Set
Fuel Pump
Fuel Filter
Coil plugs and wires
cap and rotor
hoses and belts
Thermestat and housing
I am cleaning the turbo right now. It spins freely. I'm glad no rust there.
I just don't know what that wheel is inside that I showed above in the picture.
The only problem I really don't know what I am going to do about ATM is the Intake Filter. It is gone. No more. I can't get a new one. Anybody know a good replacement?
Also anybody know where to get a front bumper in the usa?
Well wish me luck on my project. Just wish I had a garage :O
Problems I have faced.
Gas Tank rusted to hell.
In Tank filter ruined.
Fuel Pump ruined.
Fuel Lines all gummed up.
Lifters and jet valves bad.
Small hole in the Intake due to the corrosion.
So lets get to the pics. Here is the car the day I got it. And I got it for $150 usd.
NO it is not sitting on the bricks. I have a jack underthere. The brings are just saftey measure. Can never go wrong with a brick.
Here is the Turbo. What is that metal wheel in there? I never seen one. Somebody told me its a Frank Wheel?
Here is the top part of the Intake. What is that thing with all the wires coming off of it? The book says its an injection mixer but the picture isn't the same.
Same part but taken off
Intake Man. Pics of the corrosion
Small Hole
Head back from the shop
First Layer of JBWeld to fix the hole. You can see the rusted part to the left. The whole gas tank looks like that. Gonna have to have it boiled clean.
I'm currently still putting more layers of JB Weld over the damaged section of the intake. Then I will sand it down. Soon as thats done I will be putting the head back on. Intake and Exhaust, get the gas tank cleaned then start her up.
Parts bought and fixin to be replaced.
Water pump
Full Gasket Set
Fuel Pump
Fuel Filter
Coil plugs and wires
cap and rotor
hoses and belts
Thermestat and housing
I am cleaning the turbo right now. It spins freely. I'm glad no rust there.
I just don't know what that wheel is inside that I showed above in the picture.
The only problem I really don't know what I am going to do about ATM is the Intake Filter. It is gone. No more. I can't get a new one. Anybody know a good replacement?
Also anybody know where to get a front bumper in the usa?
Well wish me luck on my project. Just wish I had a garage :O