Page 1 of 1

Turboing a 4G54

Posted: Fri Jan 28, 2005 9:45 pm
by TD05
A friend's UTE has a carbie 4G54, have been thinking putting a JA TB, inlet manifold, exhaust, ECU + harness, is it doeable?, what's the compression ratio, and are the parts a bolt on affair???

Posted: Fri Jan 28, 2005 9:59 pm
by NXTIME
a 4G54 or a 4G64?

If it is a 4G64, then it is doable and the parts will bolt on. What ute is it?

Posted: Sat Jan 29, 2005 11:12 am
by sigmaproject
For a 4g54 you need Magna injection ,not Starion
http://users.chariot.net.au/~emengee/mi ... iprojects/

Posted: Sat Jan 29, 2005 7:47 pm
by mrb1
And you need a US 2.6 Starion exhaust manifold if you want to use a Mitsubishi turbo. Or find an old Sigma turbo one if you want to use a Garrett. And yes Magna manifold is the way to go for the intake.
Not sure about the ute engine but Sigma 2.6 was 8.2:1 compression. Everything is bolt on.

Posted: Sun Jan 30, 2005 10:46 pm
by quest
a few on starquestclub.com have done exactly that.
Look on http://www.starquestclub.com/cgi-bin/st ... rd=mpimods
or
http://www.starquestclub.com/?board=enginemods
for posts by "matbirch", "tainters" or "lizzord"
"shelby" posted lots of details of his turbo truck also
I they all, and "turboraider" started with tbi/stock ecu

some have boosted their non-turbo ~8.5:1 2.6 fine, with good performance

Posted: Mon Jan 31, 2005 10:33 am
by nomis
this is what im doing....yes its true i dont have a starion :o but a triton 2.6 witch im building up .. this is one of the best sites to find info on the 4g54
________
Lincoln Mark Lt

Posted: Mon Jan 31, 2005 10:46 pm
by TD05
thanx quest I 'll check those out...

Posted: Thu Feb 03, 2005 2:15 pm
by airbats801
The rule of thumb over her ein the states is dont run more than 8lbs on a stock d50 g54b block if you are looking for reliability.

Most people here just use all the g54b starion stuff, since its very straight forward

Most starion guys going mpi use the magna intake with a standalone ecu.

Posted: Thu Feb 03, 2005 10:08 pm
by TD05
nomis wrote:this is what im doing....yes its true i dont have a starion :o but a triton 2.6 witch im building up .. this is one of the best sites to find info on the 4g54
how far are you into the conversion??

too eazy

Posted: Thu Feb 10, 2005 11:44 pm
by tri26t
hey Nomis you are everywhere,
you know my tri-26t (triton 2.6 turbo) from the 4g sites,cardomain,downundertruckin, its still carbie but I have
a 4g54 manifold with starion tbi on it (TRUE) and It was a 2.6
in a starion and worked fine
2.6/auto/turbo-garret/starion ecu, all in bed together.
see ya :Phil.

Posted: Sat Feb 12, 2005 6:46 pm
by nomis
sup man yes i am everywhere (a few months ago i got sick spent 5 months in bed so i had a lot of spare time lol) but all good now im still in the middle of the whole thing... iv got a band new magan4G54 block and pistons and im getting better rods and i also have a efi TP full motor witch i will be swapping parts over and i have a 2.6 sigma motor also so im in the middle of mixing all three (but also am in the middle of huge body work so i do a bit here and there)
________
COLORADO MEDICAL MARIJUANA