Going from 8v to 16v twincam Need Help

All technical questions and answers regarding starions, being modifications to maintenance.
Post Reply
typer
Big Dorifto
Posts: 87
Joined: Fri Dec 23, 2005 12:00 pm
Location: Iceland
Contact:

Going from 8v to 16v twincam Need Help

Post by typer »

Hi, I found an 4g63 16-valve Twincam engine. My 8-valve is broken.

It's from the old 1988-1992?? eclipse car

What do you have to change ?

I have the Electric Loom And the Eclipse Computer.

Thats what happend to my engine :D

http://benzincrew.com/update01/P1010854.JPG
http://benzincrew.com/update01/P1010862.JPG
http://benzincrew.com/update01/P1010865.JPG

So what do i have to change ?
Does the engine fit corecctly to my transmission, to the motor mountings and fit nice and smooth in my engine bay?

How do i rotate the turbocharger so the inlet port is to the front ?

How do i connect the Power steering ? do i use from eclipse or starion? where to put it? how to connect it to high pressure lines ?

What Downpipe do i use? Custom maded ?

How to fit coils and do i use the same as in starion or do have to use eclipse one?

Thanks
:oops:

sorry about so many questions.


But, i know about www.projectzerog.com but those questions cant be answered there :( i dont understand that much in english.

Please help an icelandic boy here!! :beer
Image
Mitsubishi Starion '87
Mitsubishi Starion '87
Toyota Corolla '94
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

look at the sticky at the op of this page. its easier to swap the twincam head and timing gear to your starion block..
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
typer
Big Dorifto
Posts: 87
Joined: Fri Dec 23, 2005 12:00 pm
Location: Iceland
Contact:

Post by typer »

my starion block is broken if you read the threat you'll see that ;)
Image
Mitsubishi Starion '87
Mitsubishi Starion '87
Toyota Corolla '94
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

ok then to cut a long story very short:

u need a gearbox from a mitsubishi sapporo (i think thats what they were sold as in europe) 2 LT 4G52 engine, this has the right bellhousing pattern for your new engine (different to starion).

then change over the driveshaft yoke on your starion tailshaft to the sapporo one.

u will need the sapporo flywheel and starter and sandwich plate that bolts to back of block. as long as your new engine is a 6 bolt. if its 7 bolt u will need a custom made flywheel.

then change shifter housing mechanism to starion ones inside sapporo box.

then make a new water housing at the back of the head for the water outlet, and get a 86-90 corolla thermostat housing (inline type) and run that in the middle of your water transfer pipe to top radiator hose.

then modify all engine mounts to pull engine forward 15mm so crank angle sensor doesnt hit firewall.

then make a new exhaust manifold to face turbo correct direction.

then make a new dump pipe from turbo to exhaust system.

then swap ends with the throttle body on intake manifold.

power steering will have to be a custom job..

and then connect wiring etc, which will be a pain in the ass to get running right. unless ur an auto electrician, it would probably be cheaper to run an aftermarket computer..

thats why i suggested running a starion block. no stuffin round with gearbox then...
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
typer
Big Dorifto
Posts: 87
Joined: Fri Dec 23, 2005 12:00 pm
Location: Iceland
Contact:

Post by typer »

i don't understand why get another gearbox because its 6-bolt engine.
My starion is 6 bolt too.

And is that so much problem with those wires if i have the whole loom and computer of Eclipse ??
Image
Mitsubishi Starion '87
Mitsubishi Starion '87
Toyota Corolla '94
JD_Stazza_Brendan
almost postwhore
Posts: 1131
Joined: Tue Jan 25, 2005 10:46 pm
Location: Mackay, QLD, Australia

Post by JD_Stazza_Brendan »

Bellhousings will most likely be different sizes between Starion and Eclipse block.
-JA Starion with JD bits , Forged engine, Heaps of mods (parked up)
-BFII XR6 Turbo Ute , Here comes 400hp for 2k :p
-77 Mazda 323 drag car. 13bt rotary project.

Yes i have too many toys.
SOHC POWER
ROCKETMAN
Big Dorifto
Posts: 96
Joined: Wed Jan 18, 2006 3:40 pm
Location: Liverpool NSW

Post by ROCKETMAN »

typer were did you get that xrt skin for lfs?
User avatar
Starion_Turbo
Enthusiast king
Posts: 898
Joined: Wed Dec 08, 2004 5:32 pm
Location: South Australia
Contact:

Post by Starion_Turbo »

ROCKETMAN wrote:typer were did you get that xrt skin for lfs?
I think he mentioned before that he designed it.
Powerplant: Chipped stock ECU, 2044cc, 8.5:1, head intake enlarged and polished, exhaust manifold enlarged,
Balance-shafts eliminated, Intercooled, TC06 @ 10psi, 2.5" high flow exhaust system and dump pipe.
redzone
racking my brains
Posts: 5900
Joined: Thu Oct 06, 2005 10:46 pm
Location: sunshine coast qld
Contact:

Post by redzone »

typer wrote:i don't understand why get another gearbox because its 6-bolt engine.
My starion is 6 bolt too.

And is that so much problem with those wires if i have the whole loom and computer of Eclipse ??
6 bolt denoted the crank pattern, NOT the bellhousing pattern. the front wheel drive and 4 wheel drive blocks are narrow pattern, the rear wheel drive blocks are USUALLY wide pattern. measure the distance between the bottom (widest) bellhousing bolts and compare them. ALL starion blocks are wide pattern. u have a wide pattern gearbox in your car (starion box) and i'm pretty sure a narrow pattern engine (eclipse).

fitting a complete loom out of another car can be a nightmare if ur missing any parts of the loom or sensors. u also need a scan tool to read faults from a factory computer, whereas the aftermarket computers have all the info on the laptop screen in a split second, and all the wiring is brand new, so no faulty connectors or broken wires hidden where u cant see them. good luck!
Fibreglass airdams $370, fibreglass front bumpers $260, reco drag links $165, alloy radiators $925 (unpolished), h/l switch rebuilds $125, all plus freight.
Coxs Automotive (07)54433507 3/5 Service st Maroochydore Q

www.facebook.com/coxsautomotive
www.coxsautomotive.com.au
User avatar
silo
Enthusiast
Posts: 533
Joined: Fri Oct 21, 2005 2:21 pm
Location: Goulburn,NSW

Post by silo »

Eclipse is definitely narrow block ( I had a front cut).
Post Reply

Who is online

Users browsing this forum: No registered users and 17 guests