Alternative lsd for Starion?

gjgnz · Post by **gjgnz** » Thu May 25, 2006 10:49 am

I'm not really familiar with IRS setups so please excuse my ignorance. I was wondering how difficult it would be to adapt a diff head from another vehicle into the rear of a Starion. Like everyone else I want a limited slip but I'm not keen to pay big bucks for a second hand unit that is likely to need a rebuild. I was thinking along the lines of a Skyline diff as lsds are readily available new and second hand.

mitch · Post by **mitch** » Thu May 25, 2006 1:24 pm

I agree totally, i'll have a look at putting a nissan housing in the ja when i get time. I want to do this cause its easy to get decent ratios for them and also 1.5 and 2 way lsd fairly cheap. Ive put it in the 'one day basket' for now though

Rally · Post by **Rally** » Thu May 25, 2006 9:36 pm

We have been playing around in the rally staz fitting a 180sx diff, the mounting side of things has been relatively easy. The biggest issue is getting driveshafts made that make the job cost effective. The tailshaft has been made out of a 1 piece unit sourced from the wreckers with the same diameter and the yokes re welded at either end to suit. Once driveshafts are sourced will post some pics......It has been much easier to find a suitable ratio (around 4.3 - 4.7) in the nissan diffs due to the amount of imports in wreckers these days

mitch · Post by **mitch** » Fri May 26, 2006 3:35 pm

I would be very interested to see how you go with it. How much do you think the 2 drive shafts will cost? When do you think you will have pics up?

Starion VR4 · Post by **Starion VR4** » Fri May 26, 2006 3:49 pm

Have a look at LOCK RIGHT diffs, they have them to siut most vehicles, even suzuki serria's, they cost $500 for the crown wheel carrier, fitting $150, U use yr old case so no problems with mounting. They R an AUstralian company, I have 1 in my GQ Patrol works a treat, they R like a detroit locker but softer. :beer

mitch · Post by **mitch** » Fri May 26, 2006 4:00 pm

i looked into it a while ago, nothing available

sanderman · Post by **sanderman** » Fri May 26, 2006 7:19 pm

How about a Mitsy 3000 GTO diff as fitted to the four wheel steer Starion as seen in the Show & Go section first page.

SIR GSR · Post by **SIR GSR** » Fri May 26, 2006 7:21 pm

I'd go with a purpose built Ralliart diff....

Rally · Post by **Rally** » Sat May 27, 2006 9:57 am

The driveshafts will cost around $600 for the pair with us supplying ends, Albins Off Road here in Ballarat custom make shafts. The project all being well should be finished within the next couple of months. The diff has had a run in the car with a couple of cut and shut driveshafts but unfortunately were about 15 - 20 mm too short and when given shit on of the clips in the cv joint popped out from too much load. The driveshaft also managed to twist 2 mm in a fairly short run. It would have been completed by now except had a bit of an engine malfunction in the last event, so priorities changed, will keep you guys posted....

mitch · Post by **mitch** » Sat May 27, 2006 4:24 pm

WOULD YOU BE INTERESTED IN SELLING MOUNTS FOR THE CARRIER TOO, TO SAVE ME HAVING TO MAKE THEM FROM SCRATCH

CussCuss · Post by **CussCuss** » Sat May 27, 2006 6:04 pm

you really have to think about the amount of money you are saving, you can get a complete diff setup from oscar for like $800 landed now and if your after big power you can get the 3.9 and the chunky 8.5" center for not much more, compared to most commonish LSD's the price is about the same.

Rally · Post by **Rally** » Sun Jun 04, 2006 8:22 am

Correct on the $$$$ front, but supply is the issue. 3.9 is no good for rally use, it is just tto tall. Oscar has been chasing around fro us for nearly 12 mnths now with no luck so an alternative was required. With the rally car you have to have a reasonable supply of easy to get parts as breakage is inevitable from the hammering the cars cop. That's why the Nissan alternative has been a viable option.....

e-soom · Post by **e-soom** » Sun Jun 04, 2006 10:06 am

I am running the 8.5 inch diff with 4.9 ratio out of early L200,bolted straight in. L200 also come in 4.222 and 4.6.What ratio would you need.
What gearbox are you running.Would like to get a close ratio if someone has one to sell.

mrb1 · Post by **mrb1** » Sun Jun 04, 2006 8:23 pm

Rally wrote:Correct on the $$$$ front, but supply is the issue. 3.9 is no good for rally use, it is just tto tall. Oscar has been chasing around fro us for nearly 12 mnths now with no luck so an alternative was required. With the rally car you have to have a reasonable supply of easy to get parts as breakage is inevitable from the hammering the cars cop. That's why the Nissan alternative has been a viable option.....

Man I still have the works 4.6 Ralliart diff for sale. You won't break that anytime soon. It's setup for rally with a tight clutch pack, oil cooler plumbed.
It all bolts in just change the drive shaft ends to OZ spec. You can get the drive shafts from Oscar.

You told me you were worried about fitting it because of the rules and now your fitting a Nissan diff and making drive shafts WTF????

Rally · Post by **Rally** » Tue Jun 06, 2006 8:51 pm

The only time i have mentioned rules is in regards to the intercooler, which has limitations...the diff & gearbox don't.

Austarion

Alternative lsd for Starion?

Alternative lsd for Starion?

diff

Who is online