How to - Gear shift bush replacement
Fairly easy to do, just a bit time consuming.
Symptoms. My shifter would "buzz" when the revs were over 3-3.5k and was just plain annoying. There was also a small amount of slop in the shifter when in gear.
Procedure
Undo the gear knob and remove shift boot. Squeeze the wire in on the long side of the boot and move it out of the console.
Take out the box in the console and push the plastic flat panel up to get it out. Same with the window control panel. Undo all the electrics. Remove the 4 screws for the console and remove.
Then the upper part needs to come out. Undo radio knobs or whatever you have installed. Remove the trim on the sides. Undo the screws on the sides that hold the radio cradle to the metal supports. The upper console is screwed from behind through the radio cradle, if you pull it, the screw lugs will break. Once everything is undone, the upper part will slip out.
Undo the 4 screws that go through the metal surround that holds the next rubber boot in place. You'll have to pull the carpet out of the way to get at them. Once undone, pull the metal surround and rubber boot out.
Then you have the top of the gearbox. Undo the 4 bolts to remove the shifter.
That will leave you with a big oily hole!
Bush to be replaced. Mitsubishi part no. MD701577. Cost from Mitsubishi $8.90
I pulled 3 nuts off my shifter assembly to just check it and clean any crap out of it.
Also, I noticed someone prior had used silicone around the top of the assembly so I scraped it all off and made a new gasket from 0.8mm gasket paper.
The 2 bushes side by side.
The bush simply pushes on to the ball on the bottom of the shifter. I noticed the fit was much better, not loose like the old bush.
Now.....repeat the process in reverse to get it all back together. But before you do that, it's probably also a good time to jack up the car and drain that old gearbox oil and refill it, seeing as you have the top of the gearbox open and the oil will simply run in through the nice big opening you have! Gearbox should take about 2.5 litres to refill.
Out.
Gear shift bush repacement - How to
Gear shift bush repacement - How to
Last edited by Alspos on Tue Jun 24, 2014 2:20 pm, edited 1 time in total.
- perrinsohc
- Mine is bigger than yours
- Posts: 315
- Joined: Sat Mar 20, 2010 4:53 pm
- Location: Sydney/Christchurch
Al, (or anyone)
Any chance I can get the size in mm of the bottom ball on the shifter without the bush on it? (ie the internal width of the bush).
Also anyone have a pic of the pivot point of the Starion shifter as well as the diameter/width??
Any chance I can get the size in mm of the bottom ball on the shifter without the bush on it? (ie the internal width of the bush).
Also anyone have a pic of the pivot point of the Starion shifter as well as the diameter/width??
Please register your vehicle details on the AUSTRALIAN STARION REGISTRY <HERE>
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
1 x 3.2T
1 x 2.8T
3 x 2.6T's
1 x 2.0T
-
- Woodwide
- Posts: 3133
- Joined: Thu Jan 08, 2004 6:24 pm
- Location: Gold Coast
- Contact:
14.8mm but the bush is slightly worn, so minus a point 1 or 2.NXTIME wrote:Al, (or anyone)
Any chance I can get the size in mm of the bottom ball on the shifter without the bush on it? (ie the internal width of the bush).
Vulpes or Merlin?fugazi wrote: Someone on here once did a "shortshifter" with a spacer and all... and pics.
Dont remember who, and cant find it...
Who is online
Users browsing this forum: No registered users and 12 guests