Page 1 of 2

SYDNEY - TRACK DAY 2009

Posted: Tue Dec 09, 2008 10:57 am
by TOMSUN
There has been some interest in doing a Track Day.
I think it would be good to do this but separate to the Cruise.

So here it goes.

DATE: TBA (Postponed)
http://www.wakefieldpark.com.au/
4770 Braidwood Road
Goulburn (in Tirrannaville 10km South of Goulburn) NSW (2 hr drive from Sydney)
Phone: (02) 4822 2811

SPEED OFF THE STREET DAYS

• Drive your own street car $110 per day (week days)
• Australian Autosport Alliance licence $50.00 (annually) get at the track
• Approved road use helmet. Helmet hire available for $20 per day with a $50 Deposit
• Neck-to-wrist-to-ankle clothing protection (could be long sleeve shirt and long pants)
• Closed in shoes (cover ankle to toe)

Post in this thread if you are keen for a Track Day and what dates suit you and I'll compile a list.



:D iXNAY - Needs 4 weeks notice
:D thrash - In
:D WANTSOM - In
:D dirty sanchez - In
:D adrian - In pending time off work
:? TOMSUN - maybe (got a lot on at the moment)

www18u?

Posted: Tue Dec 09, 2008 1:15 pm
by thrash
i would like to get my mpi sorted before i go for a track day.. although i suppose i can just go and not push my car TOO hard :wtf:

would the track day have to be a week day?

Posted: Tue Dec 09, 2008 3:11 pm
by starion4me
i would be keen for a track day during the week as the weekend is just too many cars.

In saying that i have to give at least 4 weeks notice due to my job as they feel they can't survive with out me.

But i will do my best to attend.

Posted: Tue Dec 09, 2008 6:08 pm
by iXNAY
ill most likely come what ever day it is aslong as there is enough notice.

Posted: Tue Dec 09, 2008 8:37 pm
by WANTSOM
in :D

Posted: Mon Feb 02, 2009 4:59 pm
by dirty sanchez
Count me in.

Can we confirm that this is still happening so that I can arrange the time off work?

Posted: Mon Feb 02, 2009 6:30 pm
by thrash
for those goin from sydney, perhaps we should meet up at some place within sydney (e.g. liverpool or campbeltown or the likes, since it's on the way for most), and have a mini 'cruise' there? :beer

what time do we all wanna be going?

Posted: Mon Feb 02, 2009 6:59 pm
by starion4me
im out due to pending sale

Posted: Mon Feb 02, 2009 9:54 pm
by thrash
you have a potential buyer? lame (for us.. good for you :beer )

come with your new toy then...

Posted: Thu Feb 05, 2009 7:39 pm
by adrian
In pending time off work

Posted: Thu Feb 05, 2009 8:15 pm
by TOMSUN
I'm out until I fix my Starion.

I did a track day at Eastern Creek on Thurdays 2 weeks ago. It was for ARDC members only.

It was my first time on the a track which was a buzz. First lap was just cruising to get a feel of the car. Second lap I pushed it a bit harder and brakes were stinking and fading badly by the end of that lap. Half way around the third lap. Pop! No power and no boost! cruised back to the pits and found my intercooler piping had popped off. A bloke helped me fix it and when back out. Second turn, pop again. Back into the pits, refitted, and ditto! So I called it day. (Note: Only running 14psi) Also one of the guys folloing me said that fuel was spewing out the breather when I took a sharp right. :(

Posted: Fri Feb 06, 2009 5:11 pm
by starion4me
TOMSUN wrote:I'm out until I fix my Starion.

I did a track day at Eastern Creek on Thurdays 2 weeks ago. It was for ARDC members only.

It was my first time on the a track which was a buzz. First lap was just cruising to get a feel of the car. Second lap I pushed it a bit harder and brakes were stinking and fading badly by the end of that lap. Half way around the third lap. Pop! No power and no boost! cruised back to the pits and found my intercooler piping had popped off. A bloke helped me fix it and when back out. Second turn, pop again. Back into the pits, refitted, and ditto! So I called it day. (Note: Only running 14psi) Also one of the guys folloing me said that fuel was spewing out the breather when I took a sharp right. :(
You just need to lip (bead) your pipes so they can't come off. You can either get it done professional with a beading machine or a lot just run a bead of weld around the ends of the pipes.

Good idea is to brace the pipes as well where you can.

Posted: Fri Feb 06, 2009 5:21 pm
by www.18u
Maybe we should all join the trackday organised by the car club i am in.
It will be a private track day, and is a CAMS affiliated club. Great bunch of guys and girls, and all makes and models (not just rotaries)

It is a little more expensive than a off the street day, but i promise you it is worth it. :twisted:

Rotary Enthusiasts of New South Wales Track Day #1 2009

Sorry about this everyone, but Wakefield double booked us for the 15th. We've been moved to the following sunday

Where: Wakefield Park
When: 22nd March 2009
Why: Fine tune those driving skills
How: Fill out the entry form below.

Extra Details
All entries received before Sunday 22nd Feb go into the draw for entry fee refund for 1 person.
Entry is not confirmed until receipt of posted/faxed/emailed entry form and funds have cleared.

Entry Form
http://www.renew.asn.au/downloads/wpentry09.pdf

REgards.
RENEW CREW

Posted: Fri Feb 06, 2009 6:17 pm
by thrash
i assume you need a cams license for that one? or will the wakefield license do?

Posted: Fri Feb 06, 2009 6:18 pm
by www.18u
Wakefield will do :D